* Made in the USA *
* Patent Pending *
V-Notch/Wedge-Stop resists movement on the strand. Wide head for large bundles and to prevent roller from moving under the cable lasher. AAEROLL100P will work with 3/16 to 7/16 Guy Strand
**Order 100 or more and save $.25 cents each**

* Made in the USA *
* Patent Pending *
V-Notch/Wedge-Stop resists movement on the strand. Wide head for large bundles and to prevent roller from moving under the cable lasher. AAEROLL300R will work with 3/16 to 7/16 Guy Strand

* Made in the USA *
V-Notch/Wedge-Stop resists movement on the strand. Wide head for large bundles and to prevent roller from moving under the cable lasher. AAEROLL275P will work with 3/16 to 7/16 Guy Strand

* Made in the USA *
* Patent Pending *
V-Notch/Wedge-Stop resists movement on the strand. Wide head for large bundles and to prevent roller from moving under the cable lasher. AAEROLL100P will work with 3/16 to 7/16 Guy Strand
**Order 100 or more and save $.25 cents each**

This Block is normally used for pulling in self support or prelashed cable and is mounted with either a B, C, D, E, or F Cable Block Frame at a pole.

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable.

Cable Block Frames are used to support either the E Cable Block (GMP74055) or....

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable. Application: Light inside corners (4 ft. to 8 ft. pulls).

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable. Application: All Outside Corners (4 ft. to 50 ft. pulls)

The Dual-Lashing Aerial Cable Guide is used to guide and straighten cables as they are pulled into a lashing position.

Temporarily supports any cable up to 2-3/4 in. (70 mm) diameter on 1/4 - 3/8". (6-10 mm) suspension strand during new construction or overlashing to existing lashed cable.

D Cable Block - Supports aerial cable to 2 3/4" (70 mm) dia. Heat- treated aluminum alloy frame. Bi-directional locking lever.

H-Block is used to pull cable towards or away from corner poles or other locations. Accommodates cable from 1-1/2-3" daimeter with a 5,000lb load capacity.

This 2-3/4 in. (70 mm) single roller block is designed to support fiber optic, self-support or small copper cables at poles.

Discontinued, One On Hand
Modified Cable Leader, with nine sections and a tow hook (instead of the grip at the rear) is available for attaching a pulling eye or strand dead end.

This versatile, economical block supports any cable up to 1 1/4 in. (32mm) in diameter including coaxial, up so you can use it in CATV cabling.

This 2-3/4 in. (70 mm) single roller block is designed to support fiber optic, self-support or small copper cables at poles.

This block handles any cable or bundles up to 4" for temporarily supporting during stringing operations.

This block is functionally similar to the D cable block. This larger tool can be used with G cable lasher to handle cable up to 5". Vertical side rollers minimize cable friction during pull-in.

This economical but durable guide meets the requirements for new strand construction only. The cable shoe can accommodate a 3" cable.

This simple tool makes the lashing process smoother by maintaining the proper lead between the lasher and cable block.

This overlash cable block is perfect for temporarily suspending any cable up to 2 3/4 (70 mm) diameter on 1/4 - 3/8in (6-10 mm) diameter.

This block is used to support one cable up to 1" (25.40 mm) on new 1/4" (6.35 mm) strand. The high strength aluminum frame has a spring-loaded steel pin that keeps it locked on the strand & the cable on the nylon roller.

These rugged and lightweight corner blocks are used to guide cable and evenly distribute the load on the cable when pulling around corners.

These rugged and lightweight corner blocks are used to guide cable and evenly distribute the load on the cable when pulling around corners.

This Strand Jig Puller is used to pull out cable prior to the lashing operation. The main body of the Puller is a rugged one-piece aluminum casting.

The block is used to support up to 2¾" telephone, fiber or coaxial cable prior to the lashing operation. The frame and sheave are cast of aluminum.

The 1'' synthetic roller is a replacement part that is only used for the K468J keeper bracket.

The larger aluminum roller supports up to a 2” diameter cable for new construction or overlash operations, it also works well with winch lines.

This lightweight block is used to support up to 1” diameter cable during pull-out. The A-frame block fits over existing cable up to 2¼” in diameter.

The large rubber roller supports up to a 1-1/2" diameter cable for new construction or overlash operations, it also works well with winch lines.

This versatile block locks on 1/4" strand or fits over a 2-3/4" package of previously lashed cables. The frame will not snag loose lashing wire.

This versatile block locks on 1/4" strand or fits over a 2-3/4" package of previously lashed cables. The frame will not snag loose lashing wire.

Used to push cable blocks along strand up to 16” diameter during lashing operations. Shotguns are fabricated of a steel tube and bearing flanges.

This unit is designed to pull out up to four cables and works on packages up to 2 3/4" diameter. Opposing roller arms retain the puller to the existing cable and offer quick pole transfer.

The feeder block is used to pull out a single cable up to 1" diameter during pull out and lashing operations.

The K468J-P Replacement for Corner Block Lemco K-468J & M-370J

This lightweight block w/ Aluminu Roller is used to support up to 1-1/4” diameter cable during pull-out. The A-frame block fits over existing cable up to 2¼” in diameter.

Quick release Cross-Arm Bracket for easy installation, fitting 4.5" wide x 6.5" high crossarms. Bracket allows for 5 block positions: 0, 22, 45, 68, and 90 degrees.

Slide Stop - Dual 1" plastic rollers. This cable roller comes with two separated 1" channels for pulling multiple cables in overlash construction.

1" slap-on overlash cable roller Order 100 or more and get $1 discount at checkout.

Affordable and Built to Last Also known as slap on roller, clip on, roller, fiber roller, overlash roller, coffin roller, overlash blocks, cable rollers

Ruegg R0100 Overlash Cable Roller

Slide Stop - 3" rubber roller Designed prevent cables from catching or snagging. Supports cables up to 3" in diameter including fiber optic cables.

Slide Stop - 3" rubber roller Designed prevent cables from catching or snagging. Supports cables up to 3" in diameter including fiber optic cables.

Detent "L" Handle Safety Locking Pin w/chain for Sherman Reilly 016-010-01 Cross-arm Bracket.
Pin Diameter: 7/16"

Entire sheave is manufactured from Nylon in the same 7"x3" profile as the other options. Can be used for almost all stringing applications and cable placement.

***Sherman Reilly stringing blocks do not come with a clevis or hook SOLD SEPARATELY***

Frame is high strength aluminum alloy with sheave mounted on anti-friction ball bearings for stringing overhead ground wire.
Max Wire OD 3/4" with Max Load of 3,000lbs.

Oval Eye for use with Stringing Block
Sherman Reilly ASBE-55 NO. 6 OVAL EYE Ball Socket Connector.

Ball Clevis for use with Stringing Block PART SHER CB-55 Socket Connector.

Sherman Reilly BH-5L #1 BALL HOOK for stringing block. Socket Type Connector.

Ball Clevis for use with Stringing Block PART SHER YCB-65A Y BALL Socket Connector.