The Fluke Networks JR-LEV-1 JackRapid Punch Down Tool is a cable termination tool that is designed to give technicians maximal efficiency in cable maintenance. The JackRapid terminates jacks 8 times faster than normal tools by seating and terminating all wires at once with a simple handle squeeze. The JackRapids built-in blade cuts off excess wire, eliminating a secondary trim step. This device is designed in such a way that allows users make terminations in cramped spaces. Although the format of the JackRapid termination tool is designed to deal mainly with LEVITON 41106, 41108 and 5G108 ends it sports a replaceable blade head for use with other types of jacks.

The FSP200 optical fusion splicer uses core alignment technology, which allows the technician to reliably fuse fiber optic cables with low splice losses in as little time as seven seconds. Provides a low loss, low return loss, and reliable connection that surpasses the failure prone mechanical connector. Splice on connectors also allow for easier fiber routing, which reduces fiber preparation since the splice on connector is pre-cleaved and also eliminates the need for a splice tray.
FSP200-KIT1 includes
FSP200 fusion splicer
FCL200 cleaver.

The FCL200 cleaver provides fast and accurate cleaves that can be used with any fusion splicer and for preparing fibers for use with mechanical connectors.

When the fixed clamp is installed the fiber is securely held in place and is capable of cleaving 200 micron, 250 micron, 900 micron, 3mm, ribbon and bowtie fibers. The dust bin automatically collects all fiber end cuts for safe disposal with its spring driven mechanism.

The 1155-5005 Sidekick Plus Impulse Noise, Step TDR Test Set helps diagnose and troubleshoot problems with twisted pair cable. Easily install, qualify, and maintain DSL services.

Micro Optical Power Meters (OPM210 and OPM220) are available in standard and high-power versions for the Telco and MSO markets. Absolute and referenced power measurements ensure fast and accurate loss budget and insertion loss measurements. When placing tones on the fiber using a Tempo Communications source provides the optical power meter will definitively identify fiber optic cables.

The FI-100 fiber identifier allows the technician to quickly determine the approximate core power and signal direction in a fiber optic cable without disconnecting the fiber. Tone detect technology is employed so that the technician can uniquely trace signals once again without disconnecting fibers with potentially critical services.
FIBER IDENTIFIER + 4 FIBER CHUCKS

Fiber optic cable clamp, prepping and splicing fiber optic cables.

Fiber optic cable clamp, prepping and splicing fiber optic cables.

The Gator is used on any hardline cable after it has been stripped and cored to bevel and fully clean the center conductor.

All you have to do is hold the block of the slitter parallel to the strand and draw it along the cable and....

GMP 01820 Round Cable Slitter for 1/2 in. (14mm) to 1 in. dia. (25mm) Cable.

Discontinued with Limited Stock

Microduct Cutter

• Cleanly cuts up to 3/4 in. (19mm) mi-croduct.
  The replaceable hardened steel
• The replaceable hardened steelblade mounted in a sturdy plastic housing.
• Just align the microduct with the blade and the “V” anvil and squeeze

All you have to do is hold the block of the slitter parallel to the strand and draw it along the cable and....

GMP created ZIDS to give users a quick and easy duct cutting experience, being that the ZIDS Tool is 5 times faster than traditional methods. The tool can easily cut through half-inch pipe walls with minimal effort, as well as provide the user with an efficient method of duct slitting. The tool’s ability to cut in any direction and with a high speed of up to 25,000 RPM furthers the efficiency aspect. The ZIDS Tool is patent pending in regards to the protective nature of the product that prevents fiber damage when in use, but the primary factor that distinguishes it from other duct splitters is the 5/16” cutting diameter, which furthers the value behind the ZIDS Tool.

JONARD JIC-186 - WIRE & KEVLAR CUTTING SHEARS

High carbon stainless steel blades (heat treated to HRC 58-60) designed to cut Kevlar®, cabling insulation, tape, cable ties and other material.

JONARD JIC-375 - FIBER OPTIC STRIPPER THREE HOLE

Three hole Fiber Optic Stripper model performs all common fiber stripping functions. The first hole of this Fiber Optic Stripper strips the 1.6-3 mm fiber jacket down to the 600-900 micron buffer coating.

With preset factory settings and no adjustments required, this fiber optic stripper is designed to strip 250μm buffer coating to expose the 125μm optical fiber in fiber optic cables.

Designed to provide easy access to optical fibers in loose buffer tubes 1.2mm - 3.3 mm diameter. With 6 precision grooves buffer tube slitting is done without damage to the fiber. The blades are replaceable.

Featuring a patented 360° rotational tip for extra-wide cleaning, the FCC-125 Fiber Connector Cleaner provides exceptional cleaning performance on 1.25 mm ferrules in recessed fiber optic adapters or individual LC and MU connectors.

Featuring a patented 360° rotational tip for extra-wide cleaning, the FCC-250 Fiber Connector Cleaner provides exceptional cleaning performance on 2.5 mm ferrules in recessed fiber optic adapters or individual FC, SC, and ST connectors.

The Jonard Tools PATENTED and award-winning FOD-2000 Fiber Optic Drop Cable Slitter simplifies the slitting of drop cable jackets at mid span or end sections and is perfect for FTTH technicians working with flat fiber drop cables.

Jonard's Cabinet Slotted Screwdrivers are made with an S2 steel shank and a chrome finish for exceptional strength and long life. Our Cabinet Slotted Screwdrivers feature the following:

• Internal shank flanges to prevent the handle from slipping
• Black oxide finished tip to prevent corrosion and magnetized to hold fasteners for easy removal and installation
• Tip is cabinet slotted for easier access to hard-to-reach places
• Ergonomically designed handle for greater comfort and torque
• End of the handle is marked to be easily identifiable and features a convenient hole for hanging
• This Cabinet Slotted Screwdriver complies with ASME B107.600 and ISO 2380 standards

Jonard's Cabinet Slotted Screwdrivers are made with an S2 steel shank and a chrome finish for exceptional strength and long life. Our Cabinet Slotted Screwdrivers feature the following:

• Internal shank flanges to prevent the handle from slipping
• Black oxide finished tip to prevent corrosion and magnetized to hold fasteners for easy removal and installation
• Tip is cabinet slotted for easier access to hard-to-reach places
• Ergonomically designed handle for greater comfort and torque
• End of the handle is marked to be easily identifiable and features a convenient hole for hanging
• This Cabinet Slotted Screwdriver complies with ASME B107.600 and ISO 2380 standards

Designed for heavy duty use with an ergonomic handle, these electrician’s scissors are made of chrome vanadium steel and reinforced with a special hardening process for greater durability and cutting performance.
These scissors feature the following:

• Free fall hinge engages blades at last third of the blades, reducing hand fatigue
• Loose enough to allow fingertip operation
• One blade has a serrated edge that holds wire in place for cleaner cuts
• Notched to strip 18-20 AWG and 22-24 AWG wire with ease
• Scraper and file located on back of blade for convenience
• Nickel-plated for corrosion resistance

Designed for heavy duty use with an ergonomic handle, these electrician’s scissors are made of chrome vanadium steel and reinforced with a special hardening process for greater durability and cutting performance.
These scissors feature the following:

• Ergonomic handle provides increased comfort compared to standard scissors
• One blade has a serrated edge that holds wire in place for cleaner cuts
• Scissor-run design is perfect for cutting Kevlar® and wire
• Notched to strip 18-20 AWG and 22-24 AWG wire with ease
• Scraper and file located on back of blade for convenience
• Nickel-plated for corrosion resistance

Designed for telecom and electrical applications, these heavy duty scissors are the perfect tool for cutting cables up to 1/4” diameter and for other objects as well.
These scissors feature the following:

• One blade is serrated for a tight and secure grip while cutting
• High carbon stainless steel blades for maximum strength and durability
• Two stripping notches included for stripping 18-20 AWG and 22-24 AWG wires
• Dual component nylon and Santoprene™ grip for greater comfort and ergonomics
• Adjustable screw underneath hinge cap to configure blades to your needs

Featuring an ergonomic cable splicing knife and electrician’s scissors in a comfortable leather pouch, the TK-400 Splicer’s Kit is the perfect compact tool kit for cable splicing needs.

• Perfect for stripping 2 mm-3 mm fiber jackets off of fiber optic cables without damaging the fiber
• Coil spring reduces hand fatigue when using the tool for extended periods of time
• Conveniently located bending holes makes wire looping quick and easy
• Black oxide coated for corrosion resistance
• Cutting edges are hardened, tempered, and ground for superior cutting and stripping

Designed to shave a longitudinal access window in round FTTH riser cables and microducts for mid-span access. This riser slitting tool is perfect for making access windows on cables 8 to 14 mm (0.33” to 0.55”) in diameter without damaging the fiber inside.

Designed to clean away excess dielectric material from the center conductor of distribution or trunk cables, this cleaner is perfect for cleaning center conductors without nicking or scratching the conductor’s surface.

Designed to cleave either 900 µm buffered or 250 µm coated fiber, this fiber cleaver’s quick and easy three step operation is perfectly suited for mechanical splicing and quick field termination of fiber connectors.
This fiber cleaver features the following:

• Leaf spring scale is ruled to allow accurate and precise cleave lengths from 2 to 20 mm (0.079” to 0.79”)
• Ultra-strong carbide blade will last up to 6,000 cleaves before needing to be replaced
• Handles both single and multi-mode fibers with 125 µm cladding
• Replacement Parts: FC-4 Replacement Blade and FC-65 Replacement Leaf Spring

Featuring patent-pending Slide-Guide™ technology that provides stable and consistent cleaning performance, the FCC-300 universal fiber connector cleaner is the perfect tool for cleaning a large variety of fiber connectors.

Designed for use on LC and SC simplex and duplex connectors, this tool is perfect for inserting and extracting fiber optic connectors in high density patch panels.

Designed with a 35° beveled edge and 6 mm wide carbide blade, this fiber optic scribe is the perfect tool for scribing optical fiber.

Featuring our best selling JIC-186 Wire & Kevlar® Cutting Shears and JIC-375 Three Hole Fiber Optic Stripper in a convenient molded pouch, the TK-350 Fiber Stripper & Kevlar® Shears Kit is the essential tool kit for any fiber technician.

Featuring our ES-1964 Electrician's Scissors and JIC-375 Three Hole Fiber Optic Stripper in a convenient molded pouch, the TK-375 Fiber Stripper & Scissors Kit is the essential tool kit for any fiber technician.

The Jonard Tools FCC-120 quick click ferrule end face cleaner is designed to provide exceptional cleaning performance by cleaning MPO connectors beyond the critical fiber core area and cleaning deep into the contact area of a bulkhead adapter or connectors on fiber optic cables. The tethered dust cap provides protection for the micro fiber cleaning fabric and is an adapter for connector end face cleaning.

Designed to cut microducts cleanly and straight, this microduct cutter is perfect for cutting most microducts including tubing made from PVC, Nylon, and other materials up to 14 mm (9/16") in diameter.
This microduct cutter features the following:

• Made from polypropylene with thermoplastic rubber (TPR) grips for maximum grip and comfort
• Heat treated stainless steel blade cuts through ducts with ease
• Cuts tubing up to 14 mm (9/16") in diameter

Jonard’s fiber inspection microscope has 200x magnification, a focus wheel, and features 2.5 mm (FC/SC/ST) and 1.25mm (LC) adapters for use on most fiber connectors.

The Jonard Tools FCC-120 quick click ferrule end face cleaner is designed to provide exceptional cleaning performance by cleaning MPO connectors beyond the critical fiber core area and cleaning deep into the contact area of a bulkhead adapter or connectors on fiber optic cables. The tethered dust cap provides protection for the micro fiber cleaning fabric and is an adapter for connector end face cleaning.

This product is a replacement blade set for the RST-8514 Riser Slitting Tool. This replacement blade set includes (25) replacement blades. The blades are made of SK5 steel for high durability and long life.

This is a 4 piece replacement blade set for the CC-120 COAX Center Conductor Cleaner.
This replacement blade set features the following:

• Includes (2) V-notched and (2) straight-edge cleaning blades
• Blades are made from a rugged polycarbonate material for longer life
• Blades can be easily replaced by removing and retightening 4 easy access screws

Loading a protection sleeve onto a fiber can be tedious, even for the most experienced technicians. Plus, if they have physical impairments such as poor eyesight then it can become nearly impossible. Designed to make loading protection sleeves onto fiber quick and easy, the PSI-15 Quick Sleever® tool is ideal for aligning fiber to the holes of protection sleeves and is a real timesaver.

The Jonard CableSaber™ is the ultimate tool for gaining mid-span access to armored or thick jacketed cables 4 mm-28.6 mm (0.157”-1.125”) in diameter.

Groove Sizes:

Groove Sizes:

2.9-3.6 mm

3.6-4.4 mm

4.4-5.2 mm

5.2-6.0 mm

6.0-6.8 mm

The patented MS-306 Mid Span Slit and Ring Tool is designed to provide easy access to optical fibers in outer jackets and buffer tubes. Building on the popularity of the Jonard Tools MS-6 and MS-26 Fiber Optic Mid Span Slitting Tools, we have incorporated a ring feature in the tool to make it even more versatile.

Groove Sizes:

7.9-8.2 mm

10.7-11.0 mm

Groove Sizes:

10.2 mm

12.2 mm

15.8 mm

18.2 mm

The Jonard CableSaber™ is the ultimate tool for gaining mid-span access to armored or thick jacketed cables 4 mm-28.6 mm (0.157”-1.125”) in diameter.

• L-shaped hardened steel guide and blade guard are specially designed to allow the tool to slit open jackets while protecting the buffer tubes and fiber inside the cable
• The slitter blade is located at the top of the tool, has 1/4” of the blade exposed, and is held in place by the 3/4” L-shaped steel guide (longer guide than the JIC-4377)
• The Ringer portion of the tool is located on the back of the handle and uses a spring steel cable holder to hold the cable in place. This holder also has a sliding metal tensioner to increase the force on the cable and help ensure the jacket is cut all the way through
• Ringer can be used on 3/16"-1/2" (4.7 mm-12.7 mm) diameter cables and cuts through plastic, rubber, or fabric insulation sheathing with 0.031” (0.787 mm) or 0.018" (0.457 mm) thickness

• Patented stripping mechanism strips smoothly and efficiently every time
• Strips insulation off single and multi-stranded wires and can strip multiple wires of the same gauge simultaneously
• Strip length can be adjusted manually up to 15 mm (0.591")
• Wire cutter cuts wires as large as 14 AWG cleanly and easily
• Ergonomically designed to minimize hand fatigue during prolonged use
• High-quality laminated carbon steel stripping blades last over 30,000 strips and the tool has a life expectancy of over 150,000 uses

• Includes a free rugged carrying case, the H-20!
• Fixed jaws and ratcheting feature make it easy to grip and slit heavy-duty cable jackets, including jackets made of HDPE (High Density Polyethylene)
• Works on cables or ducts at least 1 1/2" (3.81 cm) in diameter
• Easy adjustable blade depth adjusts from 1/8" - 3/8" (3.18 mm - 9.53 mm) to handle thick-jacketed cables and ducts
• Stainless steel construction with plated steel and aluminum hardware for maximum durability and corrosion resistance
• Perfect for removing thick cable jackets on large submariner power cables, large telecom cables (600 pair+), large fiber optic ducts, or other large power cables

LEMCO Y-190 CENTER CONDUCTOR CLEANER.