JONARD ES-1964ERG Ergonomic Electrician's Scissors
Designed for heavy duty use with an ergonomic handle, these electrician’s scissors are made of chrome vanadium steel and reinforced with a special hardening process for greater durability and cutting performance.
These scissors feature the following:
- Ergonomic handle provides increased comfort compared to standard scissors
- One blade has a serrated edge that holds wire in place for cleaner cuts
- Scissor-run design is perfect for cutting Kevlar® and wire
- Notched to strip 18-20 AWG and 22-24 AWG wire with ease
- Scraper and file located on back of blade for convenience
- Nickel-plated for corrosion resistance
Klein 63050 Cable Cutters High-Leverage
High-leverage design for exceptional cutting capability of 4/0 aluminum, 2/0 soft copper, 100-pair 24 AWG communications cable, Jaw Capacity: 1.06" (2.7 cm)
Klein 63060 Ratcheting Cable Cutters
MCM Maximum Cable Capacity (Aluminum): 750 MCM (380 mm²)
MCM Maximum Cable Capacity (Copper): 600 MCM (300 mm²)
MCM Maximum Cable Capacity (Communication Cable): 1-1/8'' (28.6 mm)
Klein 64306 Grizzly Bar
A heavy, strong, multi-purpose tool that saves time and effort on the job.
The 3" (76 mm) width protects concrete when stripping forms.
Efficient blade angle and 55-1/2" (141 cm) total length provide high leverage as a crow bar and nail and spike puller.
Blade is forged and hardened alloy with keyhole nail-pulling slot in center and V-notch in tapered edge.
Very efficient nail-pulling tool even in awkward positions.
Can also be used to help align walls during tilt-up construction, to roll and align large pipe, to remove shingles and flooring, and for many other stripping and prying tasks.
KLEIN 647 - Nut Driver Set, 6-Inch Shafts, 7-Piece
The Klein Tools 7-Piece Magnetic Nut Driver Set features nut drivers with internal flanges to provide a solid, twist-resistant shaft anchor. The nut drivers are made with chrome-plated, hollow shafts to help prevent corrosion.
Klein 809-36 Lineman's Double-Faced Hammer
Designed for pole-line work. Rugged and well-balanced, with the weight to drive lag bolts. Forged, tempered-steel head is only 3-3/4'' (95 mm) long for use in tight areas. Identical faces with 1-3/4'' (44 mm) round-crown driving surface and beveled edges.
Klein 809-36MF Lineman's Milled-Face Hammer
One milled face for driving staples used in pole-line work and common, unhardened nails. Other face is smooth for driving heavier duty hardware. Rugged and well-balanced, with the weight to drive lag bolts. Forged, tempered-steel head is only 3-3/4'' (95 mm) long for use in tight areas.
Klein 85076 7 Screwdriver Set, Slotted and Phillips, 7-Piece
This 7-Piece Klein Tools Screwdriver Set contains the most frequently used, general purpose screwdrivers. Included are three cabinet-tip, two Phillips-tip, and two keystone-tip style screwdrivers. Each screwdriver features Klein's patented Tip-Ident which allows quick identification of the type of screwdriver and tip orientation.
Specifications:
- General purpose selection of the most frequently used screwdrivers
- Includes: Three cabinet-tip, two Philips-tip, and two Keystone-tip styles
- Cushion-grip handle for smooth feel and corrosion resistance
- Internal flanges inside handle provide solid, twist resistant blade anchor
- Special heat-treated shafts
- Precision-machined tip for exact fit
- Meets or exceeds applicable ASME/ANST specifiactions
- Tip-indent quickly identifies the screw driver type and up orientation
Klein 89565 Duct Stretcher
- Aligns and pulls ductwork together
- Offset handle protects hand
- Works well in tight spaces
- Designed to make drive cleat installations easier
Klein CL800 Digital Clamp Meter, AC Auto-Range TRMS, Low Impedance (LoZ), Auto Off
Klein Tools CL800 is an automatically ranging true root mean squared
(TRMS) digital clamp-meter that measures AC/DC voltage, resistance,
continuity, frequency, capacitance, and tests diodes via test-leads, and
temperature via a thermocouple probe. It also features a Low Impedance
(LoZ) mode for identifying and eliminating ghost or stray voltages.
Klein Tools’ Test and Measurement product line was exclusively designed
from the ground up by electricians for electricians. Years of field
research, combined with extensive input from electricians across
America, inspired the development of meters and electrical testers
loaded with innovative, time-saving features.
Klein D2000-9NE Lineman's Pliers, 9-Inch
These Lineman's Side-Cutting pliers feature induction hardened cutting
knives for long life. The 2000 series blades are designed for heavy-duty
cutting of ACSR, screws, nails, and most hardened wire. The
high-leverage design provides 46% greater cutting power than other plier
designs. Exclusive handle tempering absorbs the ''snap'' when cutting
wire. Pick up these Klein's and feel the difference.
Klein D203-6 Pliers, Needle Nose Side-Cutters, 6-Inch
The 6-in. Long-Nose, Side-Cutting Pliers are made of
the finest U.S. steel alloy. They are forged, precision machined,
hardened and carefully tempered for maximum strength and faultless
performance. The long nose pliers with side cutters have knives that
meet at the hinge first and then meet at least one-half of the knife
length. This precise knife-closing design increases knife life and
facilitates resharpening. Pliers are individually adjusted to meet
performance standards far exceeding application requirements.
Klein D511-6 Slip-Joint Pliers, 6-Inch
Shear-type cutter for precision wire cutting. Two versatile jaw
positions. Serrated jaws provide sure-gripping power. Nickel-chrome
plated for long life.
Klein HD213-9NETH Lineman's Pliers Bolt Thread-Holding, 9-Inch
- Pliers hinge opening holds and cleans 5/8-Inch (1.6 cm) pole line and hardware bolts or threaded rods
- High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs
- Induction hardened cutting knives for long life
- Hot-riveted joint ensures smooth action and no handle wobble
- Made in USA with Custom, US-made tool steel
- Streamlined design with rounded nose and sure-gripping, cross-hatched knurled jaw
- Unique handle tempering helps absorb the ''snap'' when cutting wire
- Precision-hardened plier head for on-the-job toughness
- Heavy-duty, oversized plastic-dipped handles for comfort and ease of identification
- ''Handform'' handles for full gripping and cutting power
Klein J2000-48 - 8'' (203 mm) Journeyman High-Leverage Diagonal-Cutting Pliers
- Diagonal Cutters with angled head design for easy work in confined spaces
- Pliers cut ACSR, screws, nails, and most hardened wire
- High-leverage design. Rivet is closer to the cutting edge for 36-percent greater cutting power than other plier designs
- Short jaws and beveled cutting edges permit close cutting of wire
- Made in USA with Custom, US-made tool steel
- Induction-hardened cutting knives for long life
- Hot-riveted joint ensures smooth action and no handle wobble
- Dual-material Journeyman™ handles provide a better grip without sacrificing tool strength and durability
- Professional-grade materials for toughness and durability
- Exclusive handle tempering absorbs the ''snap'' when cutting wire
Klein J213-9NETP Side Cutting Pliers Fish Tape Pulling
Quickly and easily pulls 1/8'' (3 mm) or 1/4'' (6 mm) flat steel fish
tape without damaging the tape. High-leverage design. Rivet is closer
to the cutting edge for 46% greater cutting and gripping power than
other plier designs. Induction hardened cutting knives for long life.
Hot-riveted joint ensures smooth action and no handle wobble.
Streamlined design with sure-gripping, cross-hatched knurled jaws.
Klein J502-10 Journeyman™ Pump Pliers, 10"
Klein Tools 10 inch (254 mm) Pump Pliers feature a secure tongue and groove design for a non-slip grip even when heavy pressure is applied. It has a tension-loaded joint to reduce handle wobble for sure gripping. Plastic-dipped handles provided added comfort and ease of identification.
