9053 E Lashing wire clamp Used to secure a terminating lashing wire to the strand. Comprised of a one-piece jaw, two washers, two nuts, and a square shank stud. Bug Nut
Bugnut also stock Hubbell 9000 E Clamp

D Cable Lashing Clamp used in aerial construction to secure terminating lashing wire or ground wire to a strand Attaches 1/4"(6mm) to 7/16" (16mm) Made in the USA

Stainless Steal Lashing Wire Type 430 Lashing Wire Size: .045 / 1200' per coil. Stainless steel lashing wire is used in a lasher or combination of cables to a supporting strand. It is a specially controlled annealing process, which yields a uniform fine grain strand structure throughout the wire length.
Alloy: 430 Diameter: 45 Coil Diameter: 5.38 in Coil Width: 1.81 in

Stainless Steel Lashing Wire Type 302 Lashing Wire Size: .045 / 1200' per coil. used in a lasher to lash a cable or combination of cables to a supporting strand. It is a specially controlled annealing process, which yields a uniform, fine grain strand structure thought the wire length.

Stainless Steel Lashing Wire Type 316 Lashing Wire Size: .045 / 1200' per coil Used for Coastal Environments. Stainless steel lashing wire is used in a lasher to lash a cable or combination of cables to a supporting strand. It is a specially controlled annealing process, which yields a uniform. Fine grain strain structure throughout the wire length.

Stainless Steel Lashing Wire Type 302 .038 1600' per coil. combines good corrosion resistance and formability at reasonable cost, and is suited for most environments. It is not recommended for use within 25 miles (40km) of salt water. Lashing wire 038302 1600' .038 302 .

DCD 61010-20Lashing Wire Disp. Mtl. Reel, 316 SS, 0.061", 650 Ft/coil
The difference between DCD Lashing Wire and other lashing wires isn’t visible to the eye. While all lashing wires may look and feel alike, DCD lashing wire is specially annealed for extra durability where the lash meets the strand. Wound in continuous coils for easy payout, DCD lashing wires won’t come back to haunt you. Instead, the lash holds tight and stays even. DCD gives you 14 choices of size and types: Aluminum, galvanized, various grades of stainless and non-metallic. All come in popular sizes to match any job, and while our sizes and types vary, our quality doesn’t. Disposable Metal Reels: Pre-coiled on 6" aluminum reels, to fit K lashers with a 1-1/4” mounting post. (CSE K & Special K lashers).
650 feet per spool.
Stainless Steel Lashing Wire

A screw type grip used to temporarily fasten lashing wire under tension before placing a permanent clamp like or D or E lashing wire clamp. Grip works with any size lashing wire. Single groove accommodates any size strand.

The GMP ZB manual cable lasher will lash up to 1 1/4 diameter cable on new construction only. Simple in execution, this lasher is designed to be used in those situations where there is little room and you need to lash a 130 ft span or less. GMP 71517 ZB MANUAL CABLE LASHER.

Lashing Wire (150ft coil in tube) for the GMP ZB manual cable lasher . This Lashing wire must be used with the 71517 ZB Lasher only.

The lashing wire coil contains 150 feet of .045 inch diameter 400 series stainless wire in a waxed cylinder 2 X 13 1/2 inches long.

A screw type grip used to temporarily fasten lashing wire under tension before placing a permanent clamp like or D or E lashing wire clamp. Grip works with any size lashing wire. Single groove accommodates any size strand.

Special wrench for replacing drive wheels on the J2 lasher.
Two needed to replace wheel 2 Required - J2/C2