The FSP200 optical fusion splicer uses core alignment technology, which allows the technician to reliably fuse fiber optic cables with low splice losses in as little time as seven seconds. Provides a low loss, low return loss, and reliable connection that surpasses the failure prone mechanical connector. Splice on connectors also allow for easier fiber routing, which reduces fiber preparation since the splice on connector is pre-cleaved and also eliminates the need for a splice tray.
FSP200-KIT1 includes
FSP200 fusion splicer
FCL200 cleaver.

The OTDR 800 is the newest handheld OTDR from Ripley’s ODM® brand that provides test technicians and contractors with an all-in-one solution for testing optical reflection and loss in fiber networks.

The 1155-5005 Sidekick Plus Impulse Noise, Step TDR Test Set helps diagnose and troubleshoot problems with twisted pair cable. Easily install, qualify, and maintain DSL services.

The fiber optic cable EZ-Exit tool eliminates damage to your fiber by easily guiding fiber optic cable past the sharp edges of a manhole chimney. The easy clamping feature allows the tool to be quickly installed in less than 30 seconds, reducing the total setup time of a fiber pull. Provides a rigid, low friction shoe that guides fiber over the sharp edges at the top and bottom of a manhole chimney while maintaining a bend diameter of 45” to accommodate up to some of the largest fiber cables.

The FI-100 fiber identifier allows the technician to quickly determine the approximate core power and signal direction in a fiber optic cable without disconnecting the fiber. Tone detect technology is employed so that the technician can uniquely trace signals once again without disconnecting fibers with potentially critical services.
FIBER IDENTIFIER + 4 FIBER CHUCKS

Pulser Ground Fault Locator identifies the exact location of even the smallest breaks in insulation by “pulsing” a high-voltage signal that radiates into the earth at the location of the faults. With the A-frame mounted receiver, a visual analog meter points the way to the source of the voltage.

The Marker-Mate Electronic Marker Locator (EML-100) is designed to locate buried electronic markers, including Tempo OmniMarker™ and UniMarker™ models at industry standard frequencies. With the updated capability of detecting nine different electronic marker types simultaneously, when in “scan” mode (power, European power, water, sanitary, telephone, fiber optic, gas, cable TV, non-potable water).

Select Spike Marker Model

SELECT OmniMarker II MODEL

Tracker II can be used on active or dead systems. Now you can trace the path and determine the depth of buried wires, cables, and metallic pipes or conduit and find the ends of a cut cable without having to deactivate the systems.

The FCL200 cleaver provides fast and accurate cleaves that can be used with any fusion splicer and for preparing fibers for use with mechanical connectors.

When the fixed clamp is installed the fiber is securely held in place and is capable of cleaving 200 micron, 250 micron, 900 micron, 3mm, ribbon and bowtie fibers. The dust bin automatically collects all fiber end cuts for safe disposal with its spring driven mechanism.

Designed to perform live testing with OLT equipment, this PON Power Meter with APC connectors is perfect for use during FTTx/PON service turn-up or maintenance.

Fiber optic cable clamp, prepping and splicing fiber optic cables.

Fiber optic cable clamp, prepping and splicing fiber optic cables.

Micro Optical Power Meters (OPM210 and OPM220) are available in standard and high-power versions for the Telco and MSO markets. Absolute and referenced power measurements ensure fast and accurate loss budget and insertion loss measurements. When placing tones on the fiber using a Tempo Communications source provides the optical power meter will definitively identify fiber optic cables.

TM-700 DSL compatible in both Monitor and Talk modes, the TM-700’s LCD screen makes reading polarity, voltage, current, and ringing frequencies easier than ever, and clearly shows speed dials and recent numbers for faster access.
TM-700 features over-voltage and over-current detection for safer operation and also features an intercom mode, a built-in toner for pair tracing, and DTMF detection and measurement

Jonard’s fiber inspection microscope has 200x magnification, a focus wheel, and features 2.5 mm (FC/SC/ST) and 1.25mm (LC) adapters for use on most fiber connectors.

Designed to cleave either 900 µm buffered or 250 µm coated fiber, this fiber cleaver’s quick and easy three step operation is perfectly suited for mechanical splicing and quick field termination of fiber connectors.
This fiber cleaver features the following:

• Leaf spring scale is ruled to allow accurate and precise cleave lengths from 2 to 20 mm (0.079” to 0.79”)
• Ultra-strong carbide blade will last up to 6,000 cleaves before needing to be replaced
• Handles both single and multi-mode fibers with 125 µm cladding
• Replacement Parts: FC-4 Replacement Blade and FC-65 Replacement Leaf Spring

Tele-Mate® Telephone Test Set is
designed to help technicians install, service and maintain voice service with ease.
Able to tackle the complexities of today’s analogue telecom lines, the
TM-500 offers the convenience of line powered (no battery needed) operation
and useful features like high impedance monitor that is data and DSL safe,
polarity test, speed dial, last number dialled and pulse dialling making a technician
more productive.

QuicKleen^™ is a unique solvent blend that cleans completely, leaves no residue, and evaporates quickly. QuicKleen Fiber EndFace Cleaner is available in a convenient 2-fl oz/60-ml spray package, and as part of an all-inclusive kit.

Type FOTM Anhydrous Isopropyl Alcohol has essentially no water content. Type FOTM is great for cleaning fiber optics and associated equipment. It quickly removes dust, oils, and contaminants, while leaving no residue.

Featuring patent-pending Slide-Guide™ technology that provides stable and consistent cleaning performance, the FCC-300 universal fiber connector cleaner is the perfect tool for cleaning a large variety of fiber connectors.

Designed to test the continuity of RJ45, RJ12, and RJ11 connectorized cables, this cable tester checks and troubleshoots pin connections in network and telecom cables.

Designed to test the continuity of RJ45, RJ12, and RJ11 connectorized cables, this cable tester checks and troubleshoots pin connections in network and telecom cables.

Loading a protection sleeve onto a fiber can be tedious, even for the most experienced technicians. Plus, if they have physical impairments such as poor eyesight then it can become nearly impossible. Designed to make loading protection sleeves onto fiber quick and easy, the PSI-15 Quick Sleever® tool is ideal for aligning fiber to the holes of protection sleeves and is a real timesaver.

FiberKleen™ towelette dispenser contains 175 lint-free, high-quality microfiber
towels that are used to clean ferrules, bulkheads and fiber endfaces.
The engineered design of the nonwoven, highly absorbent towel traps the dirt and debris
re-moved from ferrules, making cleaning easier and more effective. Variety of swabs also available.

New SqueekyKleen™ cleans and fans fiber in two wipes without alcohol, saving time and money. No follow-up with alcohol required to get fibers squeaky clean and separated when prepping for splicing.

Type FOTM Anhydrous Isopropyl Alcohol has essentially no water content. Type FOTM is great for cleaning fiber optics and associated equipment. It quickly removes dust, oils, and contaminants, while leaving no residue.

Type FO™ is great for cleaning glass fiber or connector end faces for better light transmission performance. Type FO™ quickly removes dust, oils, and contaminants, while leaving no residue.

Polywater’s non-woven FiberKleen™ Towelettes trap dirt and absorb contaminants from fiber optic cable and optical equipment. A smooth wiping surface and durable material promote easy, effective cleaning.

Type RP™ is available in convenient pre-saturated towelettes and cable prep kits. Pre-saturated wipes are a great option for field use. The towels are durable and non-linting. The pouch package limits vapor exposure and eliminates spill and splash hazards.

Type FO™ is great for cleaning glass fiber or connector end faces for better light transmission performance. Type FO™ quickly removes dust, oils, and contaminants, while leaving no residue.