The Air Compressor is designed specifically for use with our Micro Fiber Cable Blowing Machines. This reliable & efficient screw compressor, powered by a gasoline engine, provides a maximum working pressure of 220 psi (15 bar) with 35.3cfm (1000 litres/m) flow.

AIRSTREAM MICRO FIBER BLOWING MACHINE GMP 89300
AIR STREAM Fiber Blower

GMP 89003 TORNADO
Designed to be safe, fast and effective, even on tough terrain, the "Tornado" cable blowing machine will move fiber optic cable of 0.23 to 1.25 in. (5.84-32 mm) diameter at speeds to 300 ft./min. (90 m/min.) into pre-installed innerduct or direct-buried duct. It can accommodate innerduct from .47 to 2.48 in. (12-63 mm). A conversion kit allows the Tornado to place 12.7/10mm, 12/10mm or 10/8mm micro duct into the innerduct.

GMP 74099, Brass Cable Guiding Heads, are screwed on to the end of the cable to reduce friction during cable blowing. these bullet heads are constructed of corrosion resistant brass and made for repeated use.
Size OD: 7mm (0.28")

GMP 74097, Brass Cable Guiding Heads, are screwed on to the end of the cable to reduce friction during cable blowing. these bullet heads are constructed of corrosion resistant brass and made for repeated use.
Size OD: 6mm (0.24")

The 250CFM Compressor Aftercooler has been designed to cool compressed air and remove water droplets prior to entering a GMP Cable Blowing Machine.Features a heavy-duty moisture separator and coalescing filter to trap moisture and condensed oil.

GMP Tornado Cable Blowing Duct Seals
Note: Cables 10.5mm and larger utilize the standard belt. Cables below 10.5mm require a dedicated belt.
DUCT SEALS (O.D. Controlled)

GMP Tornado Cable Blowing Duct Clamps
Cables 10.5mm and larger utilize the standard belt. Cables below 10.5mm require a dedicated belt.
DUCT CLAMPS (O.D. Controlled)

GMP Tornado Cable Blowing, Cable Guides
Always use a Cable Collet on the cable exit side. If you use either 6-9 mm or 9-12 mm cable, use a Cable Guide on the cable in feed side, for anything larger than these sizes.
CABLE COLLETS (6-34 MM) & GUIDES (6-12 MM)

GMP CABLE SEALS PLUGS (6-34mm) 10/PK
Select the Cable Seals that match your cable size.

In order to configure your Tornado to work with your specific cable requirements you must select items below that match your duct and cable size.
CABLE SEAL PLUGS (6-34 MM)

In order to configure your JetStream to work with your specific cable requirements you must select items below that match your duct and cable size
CABLE SEALS (6-28 MM)

In order to customize your new "Air Stream" to your application, we ask that you pick, one each from the lists below, the Tube Collet and Clamp Assembly P/N, the Cable Guide Assembly P/N and the Cable Collet Assembly P/N.
TUBE COLLET AND CLAMP ASSEMBLIES

In order to customize your new "Air Stream" to your application, we ask that you pick, one each from the lists below, the Tube Collet and Clamp Assembly P/N, the Cable Guide Assembly P/N and the Cable Collet Assembly P/N.
SPARE TUBE SEAL O RING (5 Pack)

In order to customize your new "Air Stream" to your application, we ask that you pick, one each from the lists below, the Tube Collet and Clamp Assembly P/N, the Cable Guide Assembly P/N and the Cable Collet Assembly P/N.
CABLE GUIDE ASSEMBLIES

In order to customize your new "Air Stream" to your application, we ask that you pick, one each from the lists below, the Tube Collet and Clamp Assembly P/N, the Cable Guide Assembly P/N and the Cable Collet Assembly P/N.
SPARE CABLE SEAL (5 Pack)

GMP 89003 TORNADO
Designed to be safe, fast and effective, even on tough terrain, the "Tornado" cable blowing machine will move fiber optic cable of 0.23 to 1.25 in. (5.84-32 mm) diameter at speeds to 300 ft./min. (90 m/min.) into pre-installed innerduct or direct-buried duct. It can accommodate innerduct from .47 to 2.48 in. (12-63 mm). A conversion kit allows the Tornado to place 12.7/10mm, 12/10mm or 10/8mm micro duct into the innerduct.

The fiber optic cable EZ-Exit tool eliminates damage to your fiber by easily guiding fiber optic cable past the sharp edges of a manhole chimney. The easy clamping feature allows the tool to be quickly installed in less than 30 seconds, reducing the total setup time of a fiber pull. Provides a rigid, low friction shoe that guides fiber over the sharp edges at the top and bottom of a manhole chimney while maintaining a bend diameter of 45” to accommodate up to some of the largest fiber cables.

Polywater® Prelube 2000™ reduces frictional drag during the blowing of outside plant cable into duct. It increases the length of cable that can be blown in a single shot.

Polywater® Prelube 5000™ reduces frictional drag during the blowing of small diameter fiber optic microcable into microtube duct. It increases the length of cable that can be blown in a single shot.

Polywater® Prelube 2000™ reduces frictional drag during the blowing of outside plant cable into duct. It increases the length of cable that can be blown in a single shot.