2" RIGID Pipe, SIDEWALK GUY PIPE H-2.0"x 10' REPUBLIC
2" RIGID PIPE STICK IS 10 ft. USED FOR RISERS, SERVICE ENTRANCES, QUEENSPOST PIPE. Queens Post Pipe
Pipe size: 2" rigid with one threaded coupler. Where there is insufficient space for standard guying and where head clearance must be maintained used as a queen's post pipe. 37lbs. one10ft.stick.
" Must Ship LTL Freight"
-Due to the 10 ft length, this must ship LTL Freight.
-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
2-1/2" RIGID Pipe, SIDEWALK GUY PIPE 2.5"x 10' REPUBLIC
2-1/2" RIGID PIPE STICK IS 10 ft. USED FOR RISERS, SERVICE ENTRANCES, QUEENSPOST PIPE. Queens Post Pipe
Pipe size: 2.5" rigid with one threaded coupler. Where there is insufficient space for standard guying and where head clearance must be maintained used as a queen's post pipe. 37lbs. one10ft.stick.
" Must Ship LTL Freight"
-Due to the 10 ft length, this must ship LTL Freight.
-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
3" RIGID Pipe, SIDEWALK GUY PIPE H-3"x 10' REPUBLIC
3" RIGID PIPE STICK IS 10 ft. USED FOR RISERS, SERVICE ENTRANCES, QUEENSPOST PIPE. Queens Post Pipe
Pipe size: 3" rigid with one threaded coupler. Where there is insufficient space for standard guying and where head clearance must be maintained used as a queen's post pipe. 37lbs. one10ft.stick.
" Must Ship LTL Freight"
-Due to the 10 ft length, this must ship LTL Freight.
-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
3/4" Jaw - Eye Turnbuckle Take Up 12'' VSP 320595-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320595-I • Jaw-Eye Turnbuckles .
• Size - 3/4'' • Take Up - 12'' • Heavy duty.
• Break Strength Lbs. - 26,000.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.
3/4" Jaw - Jaw Turnbuckle Take Up 12'' VSP 320602-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320598-I • Jaw-Jaw Turnbuckles .
• Size - 3/4'' • Take Up - 12'' • Heavy duty.
• Breaking Strength - 26,000 Lbs.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.
3/4" Jaw - Jaw Turnbuckle Take Up 18'' VSP 320598-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320598-I • Jaw-Jaw Turnbuckles .
• Size - 3/4'' • Take Up - 18'' • Heavy duty.
• Breaking Strength - 26,000 Lbs.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.
5/8" Jaw - Eye Turnbuckle Take Up 12'' VSP 320597-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320597-I • Jaw-Eye Turnbuckles .
• Size - 5/8'' • Take Up - 12'' • Heavy duty.
• Break Strength Lbs. - 17,500.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.
5/8" Jaw - Jaw Turnbuckle Take Up 12'' VSP 320601-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320598-I • Jaw-Jaw Turnbuckles .
• Size - 5/8'' • Take Up - 12'' • Heavy duty.
• Breaking Strength - 26,000 Lbs.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.
8" Standoff Wireless Wall Mounts ANTVSPWWM01
Standoff Wireless Wall Mounts 8"ANT VSP WWM01
Use to install panel or whip antennas.
• U-bolts for 2-3/8'' and 3-1/2” mounting pipes.
• Mounting holes are 11/16'' on 6'' centers.
• Hardware to mount to hollow or solid walls.
Order mounting pipes separately.
All-Threaded Galvanized Rod 3/4" X 12' PORT 17648
All Thread Rod 3/4 inches X 12 feet,hot dipped galvanized. ASTM A307 Grade B
All thread rod, commonly referred to as fully threaded rod, redi-rod, continuously threaded rod, TFL rod, and abbreviated ATR is used for general purpose fastening for anything from an anchor bolt to a through bolt. A variety of grades and materials are available.
" Must Ship LTL Freight"
-Due to the 10 ft length, this must ship LTL Freight.
-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
All-Threaded Galvanized Rod 5/8" X 12' PORT 13917
All Thread Rod 5/8 inches X 12 feet,hot dipped galvanized. ASTM A307 Grade B
All thread rod, commonly referred to as fully threaded rod, redi-rod, continuously threaded rod, TFL rod, and abbreviated ATR is used for general purpose fastening for anything from an anchor bolt to a through bolt. A variety of grades and materials are available.
" Must Ship LTL Freight"
-Due to the 10 ft length, this must ship LTL Freight.
-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
Braceless Crossarm Gain PX182A Crossarm Range: 4-1/2 " TO 6"
Braceless crossarm gains improve the stability of the crossarm and eliminate the need for crossarm braces and pole gaining.The design improves the structure appearance and permits the use of fiberglass, wood, steel channel or steel tubular arms. Pole Mounting Slots 13/16 wide on top & 11/16 wide on Bottom Accommodates pole diameters from 6" - 12". Arm mounting slots are 9/16 inch wide by1-1/2 inch . Crossarm range: 4-1/2" - 6"
Double Arming Bolt 5/8" x 26" J8876
Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.
Double Span Steel Brace Cross-arm 60" H-J1510-ALL-8420
H-J1510-ALL-8420 Double Span Steel Brace 60" Span, 18" Drop
60" SPAN 18" DROP. One piece, angle steel, double span braces are used to support heavy crossarm construction. Braces are attached to the underside of the crossarm with 1/2" bolts or lag screws and fastened to the pole with a 5/8" bolt. The pole mounting section is designed to allow more than ample clearance for wrenching. Material: Hot Dip Galvanized.
PIPE CLAMP KIT CATV PV-BC-20-10
Our pipe clamp kits are made of premium galvanized steel and built to last. Their easy-to-use design of interlocking bolts, rods, and clamp halves work together to provide a secure, durable link between the parallel pipes. Fits 1.5” to 3.5” OD pipes.
PLP BPD-XARM Bird Perch Deterrent Crossarm
The BIRD PERCH DETERRENT is designed to provide protection from incidental avian contact with overhead distribution lines. It provides an economical means of reducing bird fatalities and line outages while being easily installed over distribution crossarms.
Crossarm/Angle Dimensions (W x H) 3.25" x 4.25" (8.3 x 10.8 cm)
up to 3.75" x 4.75" (9.5 x 12 cm)
Our Price: $13.79
SALE Price: $12.06
You save $1.73!
Pole Gain Plate 5 1/4" x 4" J4060
Pole gains enhance the stability of the crossarm and pole interface.
They are used where it is not possible or desirable to cut a gain in the pole.
5 1/4" x 4"
Hot Dip Galvanized
Power-Strut POSPS14634X10EG Threaded Rod 3/4" X 10' Plated
All Threaded Rod 3/4 inches X 10 feet, electroplated allthread rod.
Power Strut Straight continuous threaded rod features low-carbon steel with electro-galvanized finish for longer endurance. It measures 10-ft x 3/4-Inch Dia. It withstands maximum working load of 2710 lb.
**Sold as one stick 10ft.**
Regular Square Nut 5/8" J8563
Regular nuts are used on all types of threaded bolts and insulator pins. Considered safest to use by utility linemen. The J8563 regular square nut has a large wrenching surface.
Sidewalk Guy Clamp End J0522 Pipe size: 2" & 2-1/2" requires J931
These cast iron fittings are used with standard pipe near sidewalks and buildings where there is insufficient space for standard guying and where head clearance must be maintained.The J0522 end fitting requires a J931 guy clamp which must be ordered separately.
Square Head Machine Bolt with Nut 5/8" x 12" MSI J8812
Used for fastening poleline hardware to crossarms, poles, and other structures.
- Has a formed "cone point" to ease attachment of nut.
- Allied Bolt marking (ABI) appears on the head of each bolt.
- Hot dip galvanized to meet ASTM Specification F2329.
- Supplied with attached square nut.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Minimum thread length is 6".
- Material conforms to ASTM specification A307.
- Dimensions conform to ASME B18.2.1.
Square Head Machine Bolt with Nut 5/8" x 14" MSI J8814
Used for fastening poleline hardware to crossarms, poles, and other structures.
- Has a formed "cone point" to ease attachment of nut.
- Allied Bolt marking (ABI) appears on the head of each bolt.
- Hot dip galvanized to meet ASTM Specification F2329.
- Supplied with attached square nut.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Minimum thread length is 6".
- Material conforms to ASTM specification A307.
- Dimensions conform to ASME B18.2.1.
Square Head Machine Bolt with Nut 5/8" x 14" MSI J8814-US
Used for fastening poleline hardware to crossarms, poles, and other structures. US Made.
- Has a formed "cone point" to ease attachment of nut.
- Allied Bolt marking (ABI) appears on the head of each bolt.
- Hot dip galvanized to meet ASTM Specification F2329.
- Supplied with attached square nut.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Minimum thread length is 6".
- Material conforms to ASTM specification A307.
- Dimensions conform to ASME B18.2.1.
- US MADE
Square Head Machine Bolt with Nut 5/8" x 24" J8824
Used for fastening poleline hardware to crossarms, poles, and other structures.
- Has a formed "cone point" to ease attachment of nut.
- Allied Bolt marking (ABI) appears on the head of each bolt.
- Hot dip galvanized to meet ASTM Specification F2329.
- Supplied with attached square nut.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Minimum thread length is 6".
- Material conforms to ASTM specification A307.
- Dimensions conform to ASME B18.2.1.
Square Head Machine Bolt with Nut 5/8" x 6" MSI J8806
Used for fastening poleline hardware to crossarms, poles, and other structures.
- Has a formed "cone point" to ease attachment of nut.
- Allied Bolt marking (ABI) appears on the head of each bolt.
- Hot dip galvanized to meet ASTM Specification F2329.
- Supplied with attached square nut.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Minimum thread length is 6".
- Material conforms to ASTM specification A307.
- Dimensions conform to ASME B18.2.1.
