9053 E Lashing wire clamp Used to secure a terminating lashing wire to the strand. Comprised of a one-piece jaw, two washers, two nuts, and a square shank stud. Bug Nut
Bugnut also stock Hubbell 9000 E Clamp

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125 x 1-3/8".
• The distance between the Suspension Clamp and the above mounting hole is 5-7/8".
• Mounting hole diameters are both 11/16".
• Stamped from AISI 1018 steel.
• Hot dip galvanized to meet ASTM Specification B695.

D Cable Lashing Clamp used in aerial construction to secure terminating lashing wire or ground wire to a strand Attaches to 1/4"(6mm) to 7/16" (16mm) Made in the USA

Used to support the outer end of extension bolts when installing a parallel line to existing aerial plant.

• The distance between the Suspension Clamp and the above mounting hole is 8-3/4".
• Stock size is 1/8" x 1-3/8".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

H-4069 Crossover Clamp for 1/4" Strand

• Used in aerial construction at the mid-span to clamp two 1/4" strands together perpendicularly
• Crossover plates are tapped to eliminate the handling of loose nuts
• Stamped from AISI 1008 Steel

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125" x 2".
• The distance between the Suspension Clamp and mounting hole is 5-7/8".
• Hole diameters are 11/16" and 25/32".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

Stainless Steel Adsco Lashing Wire Clamp
Scope:

This item standard is intended for use in conjunction with CSA standard CAN/CSA-C83. This item is normally mounted on messenger strand and is used to terminate cable lashing wire.
Assembly:
The lashing wire clamp is comprised of two clamp sections, two flat washers, and two hex nut assemblies on a shouldered stud. The stud should key into one clamp section at assembly to prevent stud rotation as the nuts are tightened. This keying feature is constructed to allow proper closing of the jaws. Both ends of the stud should be suitably modified after assembly to prevent loss of the nuts.
Accommodation:
The clamp will accommodate a range of messenger strand from 3/16″ to 9’16” diameter designated strand size

• Used to secure figure 8 cable to telephone poles.
• Each Suspension Clamp is comprised of two aluminum plates, two 1/2" carriage bolts, and two square nuts.
• The plates are extruded and stamped from 6063-T6 Aluminum.
• Center hole accommodates 5/8" bolts.
• Figure 8 Three-Bolt Suspension Clamps are 6" long.
• Carriage bolt and nuts are formed from Grade 2 Steel.
• Carriage bolts and square nuts are hot dip galvanized to meet ASTM Specification A153.

• Used to secure figure 8 cable to telephone poles. Bitch clamp
  
• Each Suspension Clamp is comprised of two aluminum plates, two 1/2" carriage bolts, and two square nuts.
  
• The plates are extruded and stamped from 6063-T6 Aluminum.
  
• Center hole accommodates 5/8" bolts.
  
• Figure 8 Three-Bolt Suspension Clamps are 6" long.
  
• Carriage bolt and nuts are formed from Grade 2 Steel.
  
• Carriage bolts and square nuts are hot dip galvanized to meet ASTM Specification A153, Class C.

This clamp incorporates serpentine grooves in the two mating clamp sections to provide superior holding strength of insulated messenger wire.

MPS cable suspension clamps are used with through bolts which serve as a clamping member and are shaped to securely grip messenger wire/strand to the pole. fits 1/4 to 7/16 strand BITCH CLAMP

MSI H-J25088.1 5/8" Straight Suspension Clamp, with Flat Keeper Plate, is used with through bolts to serve as clamping member. This Flat 3-hole clamp securely grips messenger strand to pole, it uses a nut and square washer that is used between the clamp and pole for proper spacing.
Specifications:

• Firmly Grips 1/4" (6.6m) to 7/16" (16m) diameter messenger strand
• 3-Bolts,Flat
• Clamp Bolt Diameter: 1/2"
  
• Clamp Length: 5-3/4"
• Mounting Hole Diameter: 11/16" X 15/16"
• Constructed of high quality steel, hot-dipped galvanized

Angle Suspension Clamps with 1/2" track bolts and 11/16" mounting hole

Features:

• Corner attachment clamps are used for angles of 35 degrees to 60 degrees.
• Accommodates 5/8-inch diameter pole mounting bolt.
• The inner pole mounting surface is curved with integral spurs for contact stability with the pole.
• The integral thimble eyes will accept deadending devices up to 1/2-inch diameter.

Material:

• Ductile Iron - Hot Dip Galvanized

Cable suspension clamp - Straight H-J7904-ALL-5087 13/16" hole 3/4" hardware MPS cable suspension clamps are used with through bolts which serve as a clamping member and are shaped to securely grip messenger wire/strand to the pole.

1/4" to 3/8" Strand. Used to clamp to messengers where the cross at right angles to prevent wear and abrasion. The clamp sections are 1 1/2in wide and 3 1/4in long. Two 1/2in diameter bolts have oval shoulders to prevent turning when tightening. J7930

Angle Suspension Clamps with 1/2" track bolts and 13/16" mounting hole

The Maclean Senior J1070 cable messenger hanger is hot formed from 1/2" x 2" open hearth steel with a specially curved groove which permits its use on corners as well as on straight runs. Two 1/2" high carbon steel track bolts clamp the strand.
Mounting holes are 9/16" and 11/16" in diameter for a 1/2" lag screw and 5/8" through bolt.

.310-.500 STRAND .125-.184 GROUND WIRE RANGE
6-inch long curved clamping groove to conform to sag of span. For attaching medium size cable and triplex. Generously belled groove ends for angles. Teeth on feet resists downslotting. Smoothed area for stringing operation. Special nut retaining feature around body mounting bolt hole.

For attaching medium to heavy duty cable on both angle and tangent construction
Two separate clamping plate bolts allow clamping action to be independent of wood shrinkage

Provides a 12 inch clearance from the pole and is fastened with two 5/8 inch mounting bolts. Clamp plates are reversible to accept a wide range of messenger diameters.

• Hot dip Glavanisex Ductile Iron

HDG Communication Arm 3 & 2 - Position Steel Under-build, 15° Angled
15 degree angled Communication Arm 3 & 2 position Steel Under-build, galvanized for weather protection, and designed to allow for the addition of under-build cables. 36" & 24" in length from pole and 12" between mount holes.
All pole mounting and cable mounting holes are 11/16'' diameter.
WSO WB2751-B-HDG