Tangent Support Clamp .148" to .250" for 5/8" Bolt Allied Bolt 5904
Used to secure figure 8 cable to poles.
Clamp plates and J Hooks are extruded from Aluminum.
J hooks are designed to dig into poles when installed, to prevent movement during tensioning of cable.
Eliminates the need to pre-strip messenger wire.
Bolt size accommodated is 5/8".
Messenger Clamp H-PA166A Messenger Clamp .162 - .257 Strand
0162-.257 Strand or wire for 5/8 Bolt
- Small economical clamp for light duty construction
- A stringing finger is included on the clamping plate
- The back of the clamp body is recessed to fit over nut.
- A second nut secures the clamp plate and assures positive, independent clamping cation regardless of wood shrinkage
- 1-3/4 wide x 2.5" high
Messenger Clamp w/ Hook J2235
The H-J2235 is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 1 7/8". The H-J2235 is used for heavier construction.
Messenger Clamp W/Hook J2235
Messenger Clamp w/Hook PA296X
The PA296X is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 3-1/4-inches.
The PA296X is used for heavier construction.
PA296X Messenger Clamp w/Hook.
Messenger Clamp w/Hook MBA-72 .25-.72 STRAND
.25-.72 STRAND .12" - .25" GROUND WIRE
- Curved messenger groove for better support
- Body tapped for 5/8" bolt
- Hook for supporting messenger during stringing operation
- Messenger groove lip kicks-up to support cable during installation
- Independent clamping- clamp remains tight on messenger if pole shrinkage occurs
- Teeth on legs to resist movement
Material: Aluminum Alloy
Messenger Clamp w/Hook MBA-72 .25-.72 STRAND.
Messenger Clamp w/Hook MSBC-56 .398" - .56" range
May be used to support fiber
optic cable, Can be
mounted on round or flat surfaces, on a pole, or on a standoff bracket, Vertical fingers support
cable during stringing operation, Clamping Range: .398" - .56", Mounting hole is 11/16"
Material:
- Body and Keeper: Aluminum Allo
- Hardware: Steel; Hot Dip
Galvanized
Messenger Clamp w/Hook MB-62 .25-.61 STRAND
- .25-.61 STRAND .16-.25 GROUND WIRE 5/8 Bolt
- Curved groove for more cable support
- Lip on bottom groove kicks upward to support cable during installation
- Hook for supporting messenger during stringing operation
- Independent clamping - messenger remains clamped if pole shrinkage occurs
- Provides 1˝" pole clearance
- Constructed of ductile iron, hot-dip galvanized
Messenger Clamp w/Hook MB-62 .25-.61 STRAND
Messenger Clamp w/Hook J2245 3.25 inch wide
The H-J2245 is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 3 1/4". The H-J2245 is used for heavier construction.
Messenger Clamp w/Hook J2245
Messenger Clamp Medium Duty PA192A .310-.500 STRAND
.310-.500 STRAND .125-.184 GROUND WIRE RANGE
6-inch long curved clamping groove to conform to sag of span. For attaching medium size cable and triplex. Generously belled groove ends for angles. Teeth on feet resists downslotting. Smoothed area for stringing operation. Special nut retaining feature around body mounting bolt hole.
Messenger Clamp w/Hook PA292X
The PA292X is used on .109 inch to .134 inch bare or insulated messenger wire. The hook serves as a safety device and can be used in the stringing of the cable. The clamp sections and hook accommodate a 5/8-inch diameter pole mounting bolt. The clamp surface length is 1-3/4-inches.
PA292X Messenger Clamp w/Hook
