Used to secure two cable suspension clamps at opposite sides of utility pole.

• Collars are forged instead of welded for extra strength.
• Bolt provided with cone point at each end to ease starting.
• Hot dip galvanized to meet ASTM Specification F2329.
• Manufacturers mark (ABI) and tensile load designation mark (i.e.10M, 16M, 25M) appear on the unthreaded section of each bolt. ABI marking is registered with the U.S Patent Office per the Fastner Insignia Act.
• Minimum tensile strength: 13,550 lbf.
• Recommended torque value: 73 ft lb.
• Unthreaded section is 6".

• Used for placement of second cable at the same level and side of a pole as the existing cable.
  
• Cable Extension Bolts are designed to attach to the threaded ends of suspension bolts.
  
• Internally threaded section is four inches long.
  
• External threaded section is three inches long.
  
• Hot dip galvanized to meet ASTM Specification A153.

• Allied Bolt 2070 Used for placement of second cable at the same level and side of a pole as the existing cable.
  
• Cable Extension Bolts are designed to attach to the threaded ends of suspension bolts.
  
• Internally threaded section is four inches long.
  
• External threaded section is three inches long.
  
• Hot dip galvanized to meet ASTM Specification A153.

H-J7920 ARM CABLE EXTENSION
3 x 2-1/2 x 5/16 Angle Size 17-1/2-26 extension from center of Pole.
hot dip galvanized Telephone cable support.

Used to support the outer end of extension bolts when installing a parallel line to existing aerial plant.

• The distance between the Suspension Clamp and the above mounting hole is 8-3/4".
• Stock size is 1/8" x 1-3/8".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125 x 1-3/8".
• The distance between the Suspension Clamp and the above mounting hole is 5-7/8".
• Mounting hole diameters are both 11/16".
• Stamped from AISI 1018 steel.
• Hot dip galvanized to meet ASTM Specification B695.

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125" x 2".
• The distance between the Suspension Clamp and mounting hole is 5-7/8".
• Hole diameters are 11/16" and 25/32".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

Single Upset Spool Bolt 5/8" X 14" MP J2348-1/2 Minimum TENSILE STRENGTH 13,550 LBS
H-J2348-1/2 Single Upset Spool Bolt

• Shank Length: 14"
• Overall Length: 18-1/2"
• Thread Length: 6"
• Used for side-of-pole installation when supporting neutral conductors and secondary service wires
• Forged with either a single or double integral washer upset at insulator end
• Double upset provide 15⁄8" clearance between insulator and pole
• Spool bolts have 5⁄8" rolled threads
• Constructed of high quality steel, hot-dip galvanized
• Use With H- J151 spool type insulator.