Submit Search
Toggle mobile menu
Bronze Ground Rod Clamps, used with copperbonded 1/2" ground rods, provide a low resistance, secure copper-to-copper connection. These heavy-duty clamps develop a high-pressure contact between the rod and the grounding wire and can be easily disconnected when it is desired to measure resistance of the ground.
NVENT ERICO EHL58C1K 5/8" Ground Rod Connector Hammer Lock Copper These ground rod connectors help to connect grounding conductors to ground rods. They are machined from highly conductive copper to provide a low-resistance connection and to withstand ground fault currents and lightning transients.
Ground rods are driven vertically into the ground and bonded together with bare copper wire for electrical grounding." Must Ship LTL Freight"-Due to the 10 ft length, this must ship LTL Freight.-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
A 3/4" X 10' Copper Bonded Steel Ground Rod. All Blackburn ground rods have a heavy uniform covering of electrolytic copper bonded to a rigid steel core.Copper ions are forced electrically to join with the steel core, establishing acorrosion-resistant bond between the copper and the steel." Must Ship LTL Freight"-Due to the 10 ft length, this must ship LTL Freight.-Due to limited shipping cost calculations, when ordering several of these please call for accurate freight cost.
NVENT ERICO EDS58 Drive Sleeve, Grounding, 5/8 in Rod Dia.This grounding drive sleeve features copper-coated steel construction. It slides on the top of ground rods to prevent mushrooming.
These ground rod clamps have a 7/16" U-bolt and a drop forged clamping piece. It is used to clamp ground wire to 5/8" and 3/4" rods.
Bronze ground rod clamp, used with copper - bonded ground rods, provide a low resistance, secure copper to copper connection.
Bronze Ground Rod Clamps, used with copperbonded 3/4" ground rods, provide a low resistance, secure copper-to-copper connection. These heavy-duty clamps develop a high-pressure contact between the rod and the grounding wire and can be easily disconnected when it is desired to measure resistance of the ground.PART # H J8493
#6 guage poly ASTMB3 coated solid copper wire 500 ft. Priced per roll. Black coating
Soft # 6 bare copper wire 315 ft Priced per roll
SLINGCO crimping tools have been designed to provide reliable crimps installing full-tension or non-tension connectors. Mechanical Crimping Tools also have ergonomic handles for comfortable use and maximum leverage when making critical connections.
The Hastings shotgun hot stick that has an external operating rod. This style of clampstick puts an easy to control hook on the end of an insulated hot stick designed for installing hot-line and grounding clamps.Hasting 8104, Hasting 8106 & Hasting 8108
Shield bond connector featuring a longer and stronger stud to accommodate two bond braids with eyelets, does not include the insulating shoe.The 4462-SN shield bond connector is an improved version of the popular 4462 shield bond connector, with a longer and stronger stud to easily accommodate two bond braids (with eyelets). It is specifically designed to supply greater pullout strength than the 4462 shield bond connector. The nuts have been deepened, too, making them much easier to hold and tighten. The 4462-SN shield bond connector is also designed for use with coated cable.
Screw Ground Rod provides a temporary ground where a system ground is not available. When installed, the 6' spiraled ground rod develops less resistance than straight ground rods. Actual effectiveness depends upon soil properties. The reusable Ground Rod is copper clad. The helix (spiral), handle and wing nut are bronze.
H-854 /SI-2006 SPLIT BOLTAllied Bolt Part # 854 Used to make a bonding connection between two copper ground wires.Bolt and nut formed from high-strength corrosion resistant C210 Copper.Specially designed pressure bar provides high pull-out strength.Under torque, provides high contact pressure between ground wires.Smallest two conductors accepted: 10 Sol.Largest two conductors accepted: 6 Sol.Min. wire size that can be used with Max. wire size: 16 Sol.Tested and UL listed to UL486A requirements.
Positive, all-around compression with low resistance and high pull-out values. Ideal for pigtailing, 2-way splicing or tapping to an unbroken continuous main. Heavy reinforcing ribs help locate compression dies and strengthen compressed joint.
The 54740TP is positive, all-around compression with low resistance and high pull-out values. Ideal for pigtailing, 2-way splicing or tapping to an unbroken continuous main.
The 54745TP is positive, all-around compression with low resistance and high pull-out values. Ideal for pigtailing, 2-way splicing or tapping to an unbroken continuous main.Copper Compression C Tap,Thin Wall,1 AWG (Run), 2-1 AWGColor Code Purple
The TBM5-S comes with five multi-nested color-coded die sets, which mount directly on the tool for storage and whose codes are automatically embossed on the crimped connector. Features Shure-Stake ratchet.Thomas and Betts makes the TBM5S color-keyed mechanical compression tool for C-Taps, Copper and Aluminum connectors.
Applications.
The Bashlin 336A traveling ground reduces the possibility of electric shock due to accidental contact with energized conductors during stringing operations. They are heavy duty units designed for conductors Up to 336MCM (5/8")
