• Used in drop cable installations as an attachment to the strand for either accepting the bail of drop wire clamps, or for wrapping the support wire of drop cable.
  
• Consists of high strength Aluminum jaws, and a specially shaped bolt with square nut.
  
• Jaws are extruded from 6063-T6 aluminum.
  
• Bolt and nut are formed from Grade 2 steel.
  
• Bolt and nut are hot dip galvanized to meet ASTM Specification A153, Class B3.
  
• Bolt is 3/8" diameter for additional strength.
  
• Attaches to strand sizes ranging from 1/4" (6.6M) to 3/8" (10M).

1/4" to 3/8" Strand. Used to clamp to messengers where the cross at right angles to prevent wear and abrasion. The clamp sections are 1 1/2in wide and 3 1/4in long. Two 1/2in diameter bolts have oval shoulders to prevent turning when tightening. J7930

This clamp incorporates serpentine grooves in the two mating clamp sections to provide superior holding strength of insulated messenger wire. Can be used for tangent construction or angles to 30 degrees. Designed for use with .250 inch insulated figure 8 messenger. Clamps are supplied with two track bolt assemblies and a center mounting hole.

Used in drop cable installations as an attachment to the strand for accepting the bail of Drop Wire Clamps.Tensile strength of jaws and bolt exceeds 75,000 P.S.I.Clamping range is from 1/4"(6.6M) to 7/16"(16M).Clamp is comprised of a pigtail bolt, two jaws, and a square nut.Bolt and nut are formed from Grade 2 Steel.Jaws are rolled and stamped from 1018 tempered Steel.Bolt and nut are hot dip galvanized to meet ASTM Specification A153.Jaws are mechanically galvanized to meet ASTM Specification B695.

.310-.500 STRAND .125-.184 GROUND WIRE RANGE
6-inch long curved clamping groove to conform to sag of span. For attaching medium size cable and triplex. Generously belled groove ends for angles. Teeth on feet resists downslotting. Smoothed area for stringing operation. Special nut retaining feature around body mounting bolt hole.

• 6-inch long curved clamping groove to conform to sag of span.
• Generously belled groove ends for angles.
• Teeth on feet resists downslotting.
• Smoothed area for stringing operation.
• For attaching medium size cable and triplex.
• Special nut retaining feature around body mounting bolt hole.

• .25-.61 STRAND .16-.25 GROUND WIRE 5/8 Bolt
• Curved groove for more cable support
• Lip on bottom groove kicks upward to support cable during installation
• Hook for supporting messenger during stringing operation
• Independent clamping - messenger remains clamped if pole shrinkage occurs
• Provides 1½" pole clearance
• Constructed of ductile iron, hot-dip galvanized

.25-.72 STRAND .12" - .25" GROUND WIRE

• Curved messenger groove for better support
• Body tapped for 5/8" bolt
• Hook for supporting messenger during stringing operation
• Messenger groove lip kicks-up to support cable during installation
• Independent clamping- clamp remains tight on messenger if pole shrinkage occurs
• Teeth on legs to resist movement

Material: Aluminum Alloy
Messenger Clamp w/Hook MBA-72 .25-.72 STRAND.

The PA292X is used on .109 inch to .134 inch bare or insulated messenger wire. The hook serves as a safety device and can be used in the stringing of the cable. The clamp sections and hook accommodate a 5/8-inch diameter pole mounting bolt. The clamp surface length is 1-3/4-inches.

PA292X Messenger Clamp w/Hook

• Used in drop cable installations as an attachment to strand for either accepting the bail of drop wire clamps, or for wrapping the support wire of drop cable.
  
• Clamp consists of a set of steel jaws, a 1/4" diameter “pig-tail” shaped bolt, and a hex nut.
  
• The jaws are rolled and stamped from AISI 1018 tempered steel.
  
• The bolt and hex nut are formed from Grade 2 Steel.
  
• Nut and bolt are hot dip galvanized to meet ASTM Specification A153, Class B3.
  
• Jaws are mechanically galvanized to meet ASTM Specification B695, Class 50, Type 1.
• Attaches to strand ranging in size from 1/4" (6.6m) to 7/16"(16m).