Straight Suspension Clamp 5/8" MSI H-J25088.1
MSI H-J25088.1 5/8" Straight Suspension Clamp, with Flat Keeper Plate, is used with through bolts to serve as clamping member. This Flat 3-hole clamp securely grips messenger strand to pole, it uses a nut and square washer that is used between the clamp and pole for proper spacing.
Specifications:
- Firmly Grips 1/4" (6.6m) to 7/16" (16m) diameter messenger strand
- 3-Bolts,Flat
- Clamp Bolt Diameter: 1/2"
- Clamp Length: 5-3/4"
- Mounting Hole Diameter: 11/16" X 15/16"
- Constructed of high quality steel, hot-dipped galvanized
Curved Heavy Duty Suspension Clamp 3/4" MSI H-J7902B
MSI H-J7902B Curved Heavy Duty Suspension Clamp, is constructed with curved ends to prevent damage to the messenger strand when turning small angles. It is used in conjunction with through bolts to serve as clamping member, securely grips messenger strand to the pole. A nut and square washers are used between the clamp and pole to provide proper spacing.
Specifications:
- Firmly grips 1⁄4" (6.6M) to 7⁄16" (16M) diameter messenger strand
- Furnished with two track bolts and a center mounting hole
- constructed of high quality steel, hot-dipped galvanized
- Clamp Bolt Diameter: 3/4"
- Clamp Length: 6"
- Clamp Width: 2-3/16"
- Mounting Hole Diameter: 13/16"
Beam Clamp w/ Square Head MSI SI-2181
MSI SI-2181 Beam Clamp w/ Square Head, is used to provide an electrical connection to trailers, mobile homes or other beam structures. The cup point on bolt penetrates through surface paint or oxide for intimate ground to base metal.
Specifications:
- Seperate screws to attach #14 to #6 AWG ground wires
- High strength bronze casting
- UL & CUL Listed
- Bolt Head: Square
- Beam Ground Clamp
Structure Ground Clamp
Serving Sleeve 1/4" Hubbell 6452
Hubbell 6452 Serving Sleeve, for 1/4" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.38"
Serving Sleeve 5/16" Hubbell 6453
Hubbell 6453 Serving Sleeve, for 5/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.50"
Serving Sleeve 3/8" Hubbell 6454
Hubbell 6454 Serving Sleeve, for 3/8" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.75"
Serving Sleeve 7/16" Hubbell 6455
Hubbell 6455 Serving Sleeve, for 7/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 2.00"
Serving Sleeve 1/2" Hubbell 6456
Hubbell 6456 Serving Sleeve, for 1/2" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 2.25"
Communication Arm 3 & 2 Position Steel Under-build, 15° Angled WSO WB2751-B-HDG
HDG Communication Arm 3 & 2 - Position Steel Under-build, 15° Angled
15 degree angled Communication Arm 3 & 2 position Steel Under-build, galvanized for weather protection, and designed to allow for the addition of under-build cables. 36" & 24" in length from pole and 12" between mount holes.
All pole mounting and cable mounting holes are 11/16'' diameter.
WSO WB2751-B-HDG
Structure Ground Clamp, Trailer Maclean SI-2145A
Maclean SI-2145A Structure Ground Clamp, Trailer
Used to provide an electrical connection to trailers, mobile homes, or other beam structure
High strength bronze casting; SI-2177 is steel, mechanically plated
Will accept ground wires up to AWG #6
Adsco Stainless Steel Lashing Wire Clamp LWC-304SS
Stainless Steel Adsco Lashing Wire Clamp
Scope:
This item standard is intended for use in conjunction with CSA standard CAN/CSA-C83. This item is normally mounted on messenger strand and is used to terminate cable lashing wire.
Assembly:
The lashing wire clamp is comprised of two clamp sections, two flat washers, and two hex nut assemblies on a shouldered stud. The stud should key into one clamp section at assembly to prevent stud rotation as the nuts are tightened. This keying feature is constructed to allow proper closing of the jaws. Both ends of the stud should be suitably modified after assembly to prevent loss of the nuts.
Accommodation:
The clamp will accommodate a range of messenger strand from 3/16″ to 9’16” diameter designated strand size
Reinforce Brace 1-3/8" Allied Bolt 8001
Used to support the outer end of extension bolts when installing a parallel line to existing aerial plant.
- The distance between the Suspension Clamp and the above mounting hole is 8-3/4".
- Stock size is 1/8" x 1-3/8".
- Stamped from AISI 1018 steel.
- Hot dip galvanized to meet ASTM Specification B695.
E Lashing Clamp - Bug Nut H-9053
9053 E Lashing wire clamp Used to secure a terminating lashing wire to the strand. Comprised of a one-piece jaw, two washers, two nuts, and a square shank stud. Bug Nut
Bugnut also stock Hubbell 9000 E Clamp
3 Bolt Suspension Clamp for Figure 8 Cable (.109-.134") Allied Bolt 7026
- Used to secure figure 8 cable to telephone poles. Bitch clamp
- Each Suspension Clamp is comprised of two aluminum plates, two 1/2" carriage bolts, and two square nuts.
- The plates are extruded and stamped from 6063-T6 Aluminum.
- Center hole accommodates 5/8" bolts.
- Figure 8 Three-Bolt Suspension Clamps are 6" long.
- Carriage bolt and nuts are formed from Grade 2 Steel.
- Carriage bolts and square nuts are hot dip galvanized to meet ASTM Specification A153, Class C.
Cable Extension Bolt 5/8" x 7" Allied Bolt 2070
Cable Extension Bolt 5/8" x 7" Same as GMP74109
- Allied Bolt 2070 Used for placement of second cable at the same level and side of a pole as the existing cable.
- Cable Extension Bolts are designed to attach to the threaded ends of suspension bolts.
- Internally threaded section is four inches long.
- External threaded section is three inches long.
- Hot dip galvanized to meet ASTM Specification A153.
1/4" Malleable Guy Clip Allied H-885
- For 1/4" Strand
- A heavy duty means of securing down guys and wire rope.
- Comprised of a Malleable Iron base, “U” bolt, and two hex nuts.
- All components are hot dip galvanized to meet ASTM Specification A153.
Tangent Support Clamp .148" to .250" for 5/8" Bolt Allied Bolt 5904
Used to secure figure 8 cable to poles.
Clamp plates and J Hooks are extruded from Aluminum.
J hooks are designed to dig into poles when installed, to prevent movement during tensioning of cable.
Eliminates the need to pre-strip messenger wire.
Bolt size accommodated is 5/8".
3-Bolt Suspension Clamp for Figure 8 Cable (.148-.250") Allied Bolt 7027
- Used to secure figure 8 cable to telephone poles.
- Each Suspension Clamp is comprised of two aluminum plates, two 1/2" carriage bolts, and two square nuts.
- The plates are extruded and stamped from 6063-T6 Aluminum.
- Center hole accommodates 5/8" bolts.
- Figure 8 Three-Bolt Suspension Clamps are 6" long.
- Carriage bolt and nuts are formed from Grade 2 Steel.
- Carriage bolts and square nuts are hot dip galvanized to meet ASTM Specification A153.
Reinforcing Strap 1/8" x 1-3/4" J7905
Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.
- Used in aerial construction as an added support for three-bolt suspension clamps.
- Stock size is .125 x 1-3/8".
- The distance between the Suspension Clamp and the above mounting hole is 5-7/8".
- Mounting hole diameters are both 11/16".
- Stamped from AISI 1018 steel.
- Hot dip galvanized to meet ASTM Specification B695.
Reinforcing Strap 1/8" x 2" J7908
Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.
- Used in aerial construction as an added support for three-bolt suspension clamps.
- Stock size is .125" x 2".
- The distance between the Suspension Clamp and mounting hole is 5-7/8".
- Hole diameters are 11/16" and 25/32".
- Stamped from AISI 1018 steel.
- Hot dip galvanized to meet ASTM Specification B695.
3/8" Malleable Guy-Clip Allied H-887
- for 3/8 strand
- A heavy duty means of securing down guys and wire rope.
- Comprised of a Malleable Iron base, “U” bolt, and two hex nuts.
- All components are hot dip galvanized to meet ASTM Specification A153.
5/16" Malleable Guy-Clip Allied H-886-
- For 5/16 Strand
- A heavy duty means of securing down guys and wire rope.
- Comprised of a Malleable Iron base, “U” bolt, and two hex nuts.
- All components are hot dip galvanized to meet ASTM Specification A153.
D Lashing Clamp Bug Nut 4040
D Cable Lashing Clamp used in aerial construction to secure terminating lashing wire or ground wire to a strand Attaches to 1/4"(6mm) to 7/16" (16mm) Made in the USA
B Cable Suspension Bolt 5/8" X 18" Allied Bolt 8264
Used to secure two cable suspension clamps at opposite sides of utility pole.
- Collars are forged instead of welded for extra strength.
- Bolt provided with cone point at each end to ease starting.
- Hot dip galvanized to meet ASTM Specification F2329.
- Manufacturers mark (ABI) and tensile load designation mark (i.e.10M, 16M, 25M) appear on the unthreaded section of each bolt. ABI marking is registered with the U.S Patent Office per the Fastner Insignia Act.
- Minimum tensile strength: 13,550 lbf.
- Recommended torque value: 73 ft lb.
- Unthreaded section is 6".
VISE TYPE BONDING CONNECTOR HUB GC-164 BRONZE
For connecting ribbon or braid to ribbon, braid or bus.
Side Opening Jaw facilitates easy installation.
Run Conductor Size and Type | Cu ribbon 1/4", Cu braid 1/4" |
Tap Conductor Size and Type | Cu 6 sol, Cu 6 str (7), Cu ribbon 1/4", Cu braid 1/4" |
Grounding Clamp Hubbell GC5006SH
Grounding Clamp, Copper Cable to Cable, Vice Type. 6 Gage & 6-14 Gage conductors
For copper connections-Splice, Loop deadend or service entrance
tap or grounding connections
• One piece design for easier, faster installation
• Bolt head design for use with standard ratchet wrench
• Vise design achieves high connector pressure with low wrench force
3 Bolt Clamp Marriage Guy Clamp 4"with 1/2" Bolts, 3/16" - 7/16" Strand Range H-J929
MSI H-J929 3 Bolt Marriage Guy Clamp 4"with 1/2" Bolts, 3/16" - 7/16" Strand Range
3 Bolt Clamp Marriage Guy Clamp
Specifications/Features:
- Number of Bolts: 3
- Clamp Bolt Diameter: 1/2"
- Clamp Length: 4"
- Clamp Width: 1-9/16"
- Strand Diameter: 3/16" - 7/16"
- Rolled from carbon steel with straight parallel groove that will not damage strand
- The clamping bolts have special shoulders to prevent turning when the nuts are tightening
- Construct of high quality steel, hot-dip galvanized
Not to be used as a suspension clamp
Guy Clamp One Bolt J1061
1 Bolt Guy Clamp
3⁄16"-3⁄8" Strand Range
Part Number: J1061
Bellcore Specification 8624
Rolled from carbon steel with straight parallel grooves that will not damage strand
The clamping bolts have special shoulders to prevent turning when the nuts are tightened
Constructed of high quality steel, hot-dip galvanized.
Not to be used as a suspension clamp. Use a Guy Clamp only
Sidewalk Guy Clamp End J0522 Pipe size: 2" & 2-1/2" requires J931
These cast iron fittings are used with standard pipe near sidewalks and buildings where there is insufficient space for standard guying and where head clearance must be maintained.The J0522 end fitting requires a J931 guy clamp which must be ordered separately.
B Strand Grounding Clamp "Mailbox Clamp" J7956
This grounding clamp is used to bond the cable sheath to the messenger strand. Clamp body is made with an inside keeper riding on the end of the bolt. 1/2" bolt can be removed to place the clamp over the messenger wire.
3 Bolt Clamp Marriage Guy Clamp 6" with 1/2" Bolts, 3/16" - 7/16" Strand Range H-J930
MSI H-J930 3 Bolt Marriage Guy Clamp 6" with 1/2" Bolts, 3/16" - 7/16" Strand Range
3 Bolt Clamp Marriage Guy Clamp
Specifications/Features:
- Number of bolts: 3
- Clamps clamp diameter: 1/2"
- Clamp Length: 6"
- Clamp Width: 1-9/16"
- Strand Diameter: 3/16" - 7/16"
- Rolled from carbon steel with straight parallel groove that will not damage strand
- The clamping bolts have special shoulders to prevent turning when the nuts are tightening
- Construct of high quality steel, hot-dip galvanized
Not to be used as a suspension clamp.
3 Bolt Clamp Marriage Guy Clamp 6" with 5/8" Bolts, 5/16" - 1/2" Strand Range H-J931
MSI H-J931 3 Bolt Marriage Guy Clamp 6", 5/16" - 1/2" Strand Range
3 Bolt Clamp Marriage Guy Clamp
Specifications/Features:
- Number of Bolts: 3
- Clamp Bolt Diameter: 5/8"
- Clamp Length: 6"
- Clamp Width: 1-21/32"
- Strand Diameter: 5/16" - 1/2"
- Rolled from carbon steel with straight parallel groove that will not damage strand
- The clamping bolts have special shoulders to prevent turning when the nuts are tightening
- Construct of high quality steel, hot-dip galvanized
Not to be used as a suspension clamp. Can also be used with the SideWalk Guy Clamp End J0522
ONE Bolt Suspension Clamp - Straight J1095 11/16" Hole
Length: 2-1/2"
Mounting Hole: 11/16"
*Used with through bolts to serve as clamping member
*Securely grips messenger strand to the pole
*A Nut and square washer are used between the clamp
and pole to provide proper spacing
*Consists of clamping members only - used with 5⁄8" through
bolt to tighten the clamp on wire as well as to the pole
*Firmly grips 1⁄4" (6.6M) to 7⁄16" (16M) diameter messenger strand
*Constructed of high quality steel, hot-dip galvanized
Messenger Clamp w/Hook PA296X
The PA296X is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 3-1/4-inches.
The PA296X is used for heavier construction.
PA296X Messenger Clamp w/Hook.
Messenger Clamp w/Hook PA292X
The PA292X is used on .109 inch to .134 inch bare or insulated messenger wire. The hook serves as a safety device and can be used in the stringing of the cable. The clamp sections and hook accommodate a 5/8-inch diameter pole mounting bolt. The clamp surface length is 1-3/4-inches.
PA292X Messenger Clamp w/Hook
Messenger Clamp w/ Hook J2235
The H-J2235 is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 1 7/8". The H-J2235 is used for heavier construction.
Messenger Clamp W/Hook J2235
Messenger Clamp w/Hook J2245 3.25 inch wide
The H-J2245 is used on .250 inch insulated messenger wire.These clamps are used for tangent construction or angles to 10 degrees. The hook is provided for stringing and safety. The clamp surface length is 3 1/4". The H-J2245 is used for heavier construction.
Messenger Clamp w/Hook J2245
Messenger Clamp w/Hook MBA-72 .25-.72 STRAND
.25-.72 STRAND .12" - .25" GROUND WIRE
- Curved messenger groove for better support
- Body tapped for 5/8" bolt
- Hook for supporting messenger during stringing operation
- Messenger groove lip kicks-up to support cable during installation
- Independent clamping- clamp remains tight on messenger if pole shrinkage occurs
- Teeth on legs to resist movement
Material: Aluminum Alloy
Messenger Clamp w/Hook MBA-72 .25-.72 STRAND.
Messenger Clamp w/Hook MB-62 .25-.61 STRAND
- .25-.61 STRAND .16-.25 GROUND WIRE 5/8 Bolt
- Curved groove for more cable support
- Lip on bottom groove kicks upward to support cable during installation
- Hook for supporting messenger during stringing operation
- Independent clamping - messenger remains clamped if pole shrinkage occurs
- Provides 1½" pole clearance
- Constructed of ductile iron, hot-dip galvanized
Messenger Clamp w/Hook MB-62 .25-.61 STRAND
Messenger Clamp w/Hook MSBC-56 .398" - .56" range
May be used to support fiber
optic cable, Can be
mounted on round or flat surfaces, on a pole, or on a standoff bracket, Vertical fingers support
cable during stringing operation, Clamping Range: .398" - .56", Mounting hole is 11/16"
Material:
- Body and Keeper: Aluminum Allo
- Hardware: Steel; Hot Dip
Galvanized
Messenger Clamp H-PA166A Messenger Clamp .162 - .257 Strand
0162-.257 Strand or wire for 5/8 Bolt
- Small economical clamp for light duty construction
- A stringing finger is included on the clamping plate
- The back of the clamp body is recessed to fit over nut.
- A second nut secures the clamp plate and assures positive, independent clamping cation regardless of wood shrinkage
- 1-3/4 wide x 2.5" high
2 Bolt Guy Clamp 3-3/8Lng " with 1/2" Bolts J1030/ALL 5058
1/2" TWO BOLT GUY CLAMP 3-3/8" X 1-9/16" PLATES
- Used to form guy loops that attach to anchor rods or dead-ends.
- Parallel grooves accept strand without marring.
- Plate halves align evenly for ease of installation.
- Plate length is 3-3/8" and plate width is 1-9/16".
- Strand sizes accommodated are 3/16" (2.2 M) -3/8" (10 M).
- Comprised of two plates and two 1/2" X 1-5/8" Carriage Bolts with Regular Square Nuts.
- Hot dip galvanized to meet ASTM Specification A153.
- H-J1030-ALL-5058
- This is not a suspension clamp
Sidewalk Guy Clamp End J1502 Pipe size: 2"
These cast iron fittings are used with standard pipe near sidewalks and buildings where there is insufficient space for standard guying and where head clearance must be maintained.
Sidewalk Guy Pole Plate J1501 Pipe size: 2"
These cast iron fittings are used with standard pipe near sidewalks and buildings where there is insufficient space for standard guying and where head clearance must be maintained.
Cable Suspension 1/4" x 3/8" Crossover Clamp MSI J7930
1/4" to 3/8" Strand. Used to clamp to messengers where the cross at right angles to prevent wear and abrasion. The clamp sections are 1 1/2in wide and 3 1/4in long. Two 1/2in diameter bolts have oval shoulders to prevent turning when tightening. J7930
CORNER ATTACHMENT H-P294 DOUBLE THIMBLE EYE
Features:
- Corner attachment clamps are used for angles of 35 degrees to 60 degrees.
- Accommodates 5/8-inch diameter pole mounting bolt.
- The inner pole mounting surface is curved with integral spurs for contact stability with the pole.
- The integral thimble eyes will accept deadending devices up to 1/2-inch diameter.
Material:
- Ductile Iron - Hot Dip Galvanized
Messenger Clamp Medium Duty PA192A .310-.500 STRAND
.310-.500 STRAND .125-.184 GROUND WIRE RANGE
6-inch long curved clamping groove to conform to sag of span. For attaching medium size cable and triplex. Generously belled groove ends for angles. Teeth on feet resists downslotting. Smoothed area for stringing operation. Special nut retaining feature around body mounting bolt hole.
MESSENGER HANGER 1/4"-3/8" STRAND MSI J1070
The Maclean Senior J1070 cable messenger hanger is hot formed from 1/2" x 2" open hearth steel with a specially curved groove which permits its use on corners as well as on straight runs. Two 1/2" high carbon steel track bolts clamp the strand.
Mounting holes are 9/16" and 11/16" in diameter for a 1/2" lag screw and 5/8" through bolt.
GROUND BOND 5/8" H-J1163
H-J1163 Ground/Bond 5/8"
MSI galvanized steel ground/bond clamp - Used to attach ground wires at the nut end of bolts on transmission lines
- Includes two 1½" long clamp sections and one square nut
- Constructed of high quality steel, hot-dip galvanized
- Ground Wire Diameter 3/16" - 3/8"
5/8" Jaw - Eye Turnbuckle Take Up 12'' VSP 320597-I
Turnbuckles are used as adjustable extension links to maintain proper tower clearance on assemblies at tower end.
• 320597-I • Jaw-Eye Turnbuckles .
• Size - 5/8'' • Take Up - 12'' • Heavy duty.
• Break Strength Lbs. - 17,500.
• Hot-dip galvanized
• Meets Federal Specification FF-T-791B, Type1, Form 1, Class 7.