Polywater® CF-35 CableFree® Loosener 1 qt. Bottle
CableFree® Loosener is a white, water-based, general-purpose dissolver/lubricant. It is a thick, pourable liquid for convenient loading into conduit. It dissolves waxes, bitumen, soil deposits, and lifts rust. It also provides a lubricating film to ease cable removal once the cable has broken free
- 1-quart bottle (.95 liter)
- Loosens stuck cable by softening binding agents such as wax, rust, soap, dirt, bitumen.
- Lubricates to minimize the force required to pull the cable out once it has broken free.
- Leaves empty conduit undamaged and ready for re-use after cleaning and drying.
- Lowers duct reclamation costs by eliminating expensive cut-ins.
- Limits liability. Meet NEC Code for Removal of Abandoned Cable.
QUANTITY:
As a rule of thumb, 1 quart of CableFree® Loosener should be used for every 50 feet of 1" conduit (1 liter per 15m of 2.5cm conduit). For larger conduits, the following equation provides a starting estimate of the amount of Loosener.
Cable Removal:
- Q = .02 x L x D (Metric Formula: Q = .024 x L x D)
- where: Q = quantity required in quarts (liters for metric)
- L = length of the conduit in feet (meters for metric)
- D = diameter of the conduit in inches (centimeters for metric)
Polywater® CGL-128 Communications Gel Pulling Lubricant 1gl
Polywater® Lubricant CGL 1gl is a high performance, gel cable pulling for fiber optic, copper or coaxial cable pulls. Polywater® Lubricant CGL is a high performance, gel cable pulling for fiber optic, copper or coaxial cable pulls.
Polywater® Lubricant CGL provides maximum friction reduction between cable and conduit under both low and high sidewall bearing pressures. It is slow-drying and leaves a lubricating film after its water base has evaporated. Polywater® CGL is a gel material and can be applied by hand or using Polywater’s LP Pumps. Polywater® Lubricant CGL is safe for the aquatic environment. It meets California regulation CCR 22. Polywater® CGL is suitable for use on PE and low-smoke zero-halogen (LSZH) communication cable jackets. Polywater® WCGL (winter grade) has the same characteristics as Polywater® CGL and is specially formulated for use in temperatures as low as -20°F (-30°C).
Polywater® CGL-640 Gel Communications Cable Pulling Lubricant 5gl
Polywater® Lubricant CGL is a high performance, gel cable pulling for fiber optic, copper or coaxial cable pulls. Polywater® Lubricant CGL provides maximum friction reduction between cable and conduit under both low and high sidewall bearing pressures. It is slow-drying and leaves a lubricating film after its water base has evaporated.
ONE 5-gallon (3.8 liter) pail.
Polywater® CGL is a gel material and can be applied by hand or using Polywater’s LP Pumps. Polywater® Lubricant CGL is safe for the aquatic environment. It meets California regulation CCR 22. Polywater® CGL is suitable for use on PE and low-smoke zero-halogen (LSZH) communication cable jackets. Polywater® WCGL (winter grade) has the same characteristics as Polywater® CGL and is specially formulated for use in temperatures as low as -20°F (-30°C).Polywater® Lubricant CGL is also a superior pulling lube for pulling power wire/cables into all types of conduit.
Polywater® CPL-128 Communications Cable Pulling Lubricant 1gl
Polywater® CPL 1gal Pourable Liquid Lubricant for Communications Cable Pulling. Polywater® Lubricant CPL is a high-performance, pourable liquid cable pulling lubricant formulated specifically for the communications industry. It is recommended for long fiber optic, copper-paired or coaxial cable pulls.
Polywater CPL provides maximum friction reduction between cable and conduit under both low and high sidewall bearing pressures. It is slow drying and leaves a lubricating film after its water base has evaporated. Polywater CPL is a liquid lubricant and can be applied by pouring into an up-turned duct or funnel.
Polywater® CPL-640 CPL Communications Cable Pulling Lubricant 5gl
Polywater® Lubricant CPL 5gal is a high performance, pourable liquid cable pulling lubricant for long fiber optic, copper or coaxial cable pulls.
Polywater® Lubricant CPL provides maximum friction reduction between cable and conduit under both low and high sidewall bearing pressures. It is slow-drying and leaves a lubricating film after its water base has evaporated. Polywater® CPL is a liquid lubricant and can be applied by pouring into an up-turned duct or funnel. Polywater® Lubricant CPL is safe for the aquatic environment. It meets California regulation CCR 22. Polywater® CPL is suitable for use on PE communication cable jackets.
Polywater® WCPL (winter grade) has the same characteristics as Polywater® CPL and is specially formulated for use in temperatures as low as -20°F (-30°C)
Polywater® F-128 Fiber Optic Cable Pulling Lubricant 1gl
Polywater® Lubricant F is a high performance, pourable liquid lubricant recommended for long, difficult, lightguide cable pulls. It is slow drying and leaves a lubricating film after its waterbase has evaporated. Polywater® Lubricant F will not stress crack low density polyethylene. It is compatible with all common* types of cable jackets. Polywater® Lubricant WF (winter grade) has the same characteristics as Polywater® Lubricant F and is specially formulated for use in temperatures as low as -20°F (-30°C).
Polywater® F-35 Fiber Optic Cable Pulling Lubricant 1-quarter squeeze bottle
Polywater® Lubricant F 1-quarter squeeze bottle is a high performance, pourable liquid lubricant recommended for long, difficult, lightguide cable pulls. It is slow drying and leaves a lubricating film after its waterbase has evaporated. Polywater® Lubricant F will not stress crack low density polyethylene. It is compatible with all common* types of cable jackets. Polywater® Lubricant WF (winter grade) has the same characteristics as Polywater® Lubricant F and is specially formulated for use in temperatures as low as -20°F (-30°C).
Polywater® F-640 Fiber Optic Cable Pulling Lubricant 5gl
Polywater® Lubricant F 5gl is a high performance, pourable liquid lubricant recommended for long, difficult, lightguide cable pulls.
It is slow drying and leaves a lubricating film after its water base has evaporated. Polywater® Lubricant F will not stress crack low
density polyethylene. It is compatible with all common types of cable jackets. Polywater® Lubricant WF (winter grade) has the same characteristics as Polywater® Lubricant F and is specially formulated for use in temperatures as low as -20°F (-30°C).
Polywater® FTTx-35LR Communications Lubricant 1-quart bottle with sprayer
Polywater® FTTx Fiber Lubricant makes the installation of fiber drops easy. The lubricant is concentrated, only a thin film is required for immediate tension reduction that lasts even as the lubricant dries. Spray or wipe the cable or conduit. Quick and easy to use without mess or excess lubricant.
Perfect for Fiber Optic Drops
- Includes: 1-quart (.95 liter) bottle with sprayer.
- Non-Staining, Quick Clean-Up
- Easy Application with Spray or Wipe
- Lubricates with Very Thin Film, Performs After Drying
- Compatible with Common Cable Jackets – Including Polyethylene
- Helps Prevent "Wet Link" Insertion Loss in Category 6 Data Cables
Polywater® J-640 Cable Lubricant for Heavy Cable Installations
The Most Used and Specified Cable Lubricant
Specification-grade Polywater ®
Lubricant J is a high-performance, clean,
slow-drying, water-based gel lubricant. Lubricant J provides maximum
tension reduction in all types of cable pulling. It is recommended for long
pulls, multiple-bend pulls, and pulls in a hot environment.
PRODUCT BENEFITS
• Maximum Friction Reduction:
For low cable pulling tension.
• Clean and Non-Staining:
Minimizes clean-up time.
• Field-Friendly Application: Can
be pumped, hand applied, or
distributed by Front End Pack™.
• Temperature Stable: No ruined
lubricant from freeze/thaw or hightemperature exposure.
• High Cling Factor: Stays on cable
jacket during application.
Polywater® P-128 Prelube 2000™ Cable Blowing Lubricant 1gl
Polywater® Prelube 2000™ reduces frictional drag during the blowing of outside plant cable into duct. It increases the length of cable that can be blown in a single shot. Prelube 2000™ can also be used to blow in the hollow microtubes intended to hold future microcables (use Prelube 5000™ for blowing the microcables themselves). For decades, Prelube 2000™ has been proven in the blowing of tens of thousands of kilometers of cable in over 50 countries on a variety of cable blowing machines.
Inlcudes:
1-gallon/3.8-liter jug
Polywater® P-35 Prelube 2000™ Cable Blowing Lubricant 1-qt. Squeeze Bottle
Polywater® Prelube 2000™ reduces frictional drag during the blowing of outside plant cable into duct. It increases the length of cable that can be blown in a single shot. Prelube 2000™ can also be used to blow in the hollow microtubes intended to hold future microcables (use Prelube 5000™ for blowing the microcables themselves). For decades, Prelube 2000™ has been proven in the blowing of tens of thousands of kilometers of cable in over 50 countries on a variety of cable blowing machines.
Inlcudes:
1-quart/0.95-liter squeeze bottle
Polywater® PM-8 Prelube 5000™ Microcable Blowing Lubricant 8-fl oz Squeeze Bottle
Polywater® Prelube 5000™ reduces frictional drag during the blowing of small diameter fiber optic microcable into microtube duct. It increases the length of cable that can be blown in a single shot. Prelube 5000™ is more concentrated, yet less viscous, than Prelube 2000™ (for blowing conventional fiber cables). The improved chemistry allows this product to spread further and reduce friction at extremely low coating levels. The lower viscosity allows practical application into the microtubes.
Includes:
8-fl. oz. squeeze bottle (.24 l)
